• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Sport trac 8.8


fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,792
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
I have a line on an 8.8/4.10 limited slip out of a 2002 Sport Trac. I know it's got drum brakes. Is it the same as the 91-94 Explorer axles? Trying to make sure what I'm getting into if swapping it into my 99. Thanks!
 
Last edited:


Mac

Well-Known Member
Supporting Member
V8 Engine Swap
Joined
Aug 9, 2007
Messages
5,103
Reaction score
182
Points
63
Age
77
Location
C. Wisconsin
Vehicle Year
2003
2000
199
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
Found this at Explorerfroum. Doesn't mention width or other items.
What year ford explorers do I look for as a donor for 31 spline and disc brakes? To get rear disc brakes and 31-spline axle, you need to look for a 1995 to 2001 Explorer or Mountaineer. Earlier years use drum brakes and may be 28-spline. Different vehicles may have the wrong bolt pattern, width, spline count, or brakes. A 2-door Sport Explorer may be a donor past the 2001 cut off. Also, Explorer SportTracs with production dates of August 19, 2002 through June 29, 2005 are equipped with 31-spline axles and rear disc brakes and are exactly what was in the previously listed 95-2001 Explorer. Before Aug 19, 2002, the Sport Tracs were equipped with the smaller 28-spline 8.8 axle shafts and used drum brakes. After June 29, 2005, Sport Tracs were produced with an Independent rear as found on 2002 regular Explorers.* Sport-Trac
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,792
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
Crap. Didn't realize it was 28 spline. Thanks for digging that up. More than I found in a quick search on my phone.
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,792
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
Hmm. Everything I'm looking up is mixed on the 28/31 spline question. I think I'm going to chance it. The price for the axle plus springs is hard to refuse.
 

4x4junkie

Forum Staff Member
TRS Forum Moderator
TRS 20th Anniversary
Joined
Aug 19, 2001
Messages
10,749
Reaction score
580
Points
113
Location
So. Calif (SFV)
Vehicle Year
1990
Make / Model
Bronco II
Engine Type
2.9 V6
Engine Size
2.9L V6
Transmission
Manual
2WD / 4WD
4WD
Tire Size
35x12.50R15
I think that quote has more errors in it than it has accurate information. :rolleyes:

It should be 31 spline unless someone replaced it with a Ranger axle (which I s'pose could be a possibility if someone did a SOA conversion and was too lazy to find someone who could move the perches on the original axle). I've never seen credible info myself that a 28 spline 8.8 was ever used in Explorers.

But for your own comfort you can identify it as 31 spline just by examining the axle tubes.

A 31-spline axle will have 3.25" diameter tubes all the way until about 2" before the backing plate bracket where it then tapers down to approx 2-7/8".

A 28 spline axle has 3" tubes at the pumpkin... At the mid-point before the spring perch it tapers down to just over 2-3/4", and then right before the backing plate it tapers again to approx 2-5/8".
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,792
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
Picked it up today.
Rear axle drum to drum, leaf springs, driveshaft, two front leather seats, center floor console, white instrument cluster, shifter, and two switches for $220.
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,792
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
Last edited:

4x4junkie

Forum Staff Member
TRS Forum Moderator
TRS 20th Anniversary
Joined
Aug 19, 2001
Messages
10,749
Reaction score
580
Points
113
Location
So. Calif (SFV)
Vehicle Year
1990
Make / Model
Bronco II
Engine Type
2.9 V6
Engine Size
2.9L V6
Transmission
Manual
2WD / 4WD
4WD
Tire Size
35x12.50R15
Looks like it's been sitting awhile with water-contaminated oil in it.

If the gear itself and the bearings seem OK, I'd say get some old junky flat-head screwdrivers or something and chip & scrape as much of it off as you can, then maybe follow with a stiff-bristled wire brush or wire wheel.

Turn the axle over the other way so the debris doesn't fall down inside the housing.
 

pjtoledo

Well-Known Member
Supporting Member
U.S. Military - Veteran
Joined
Oct 5, 2007
Messages
5,338
Reaction score
2,908
Points
113
Location
Toledo Ohio
Vehicle Year
20002005199
Make / Model
Fords
Engine Size
3.0 2.3
why isn't the ring gear rusted too? they were attached and submerged in the same lube??? any rust on the diff cover plate? I would thoroughly clean and inspect everything.

that looks like a job for the liquid rust removers, but that requires removing the tone ring for soaking. maybe some of the jelly type rust removers if you don't want to take it apart.
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,792
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
I'll give it a more thorough inspection tomorrow but that was the only major corrosion I noticed. Anything on the ring gear looked very minor and everything rolled very smoothly.
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,792
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
Question...
The article on our tech pages about rebuilding a Traction Lok involves removing the carrier (the second section that discusses the carbon fiber kit, which I ordered for this axle).
http://www.therangerstation.com/tech_library/rebuild_tractionlock.shtml

1) Why is this necessary?
2) Regardless of the necessity... If I can pull it out and trust that the position won't change since I'll be reinstalling the same gears and carrier, couldn't I just yank it and clean the ring on a bench (or just install a new ring)?
 

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,212
Reaction score
16,346
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.
That's a good question. I just read through that procedure and it looks to me like you can do it with the carrier in the housing. Just pull the axles so you can get the side gears out.

Give it a try.

edit; I just read that again and saw a line talking about getting the S-spring out. Apparently, that may not come out past the ring gear, depending on gear ratio. With 4.10 gears, I'm pretty sure that will be an issue for you. Of course, you never know until you open it up and look.
 
Last edited:

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,792
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
You can definitely remove the side gears and spiders from the carrier with it installed in the axle. Did that last night before reading through everything. Unless that changes with new components vs worn clutch plates, I don't understand why you'd need to have the carrier out. That said, it might simplify my issue with the tone ring.
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,792
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
I went ahead and pulled the carrier last night. Hoping to get a chance to clean the ring over the next couple of days. Worst case I'll try to remove it from the ring gear and clean it separately (and/or replace as needed).
 

bobbywalter

TRS Technical Staff
TRS Event Staff
V8 Engine Swap
TRS Technical Advisor
TRS Banner 2012-2015
TRS 20th Anniversary
Ugly Truck of Month
TRS Event Participant
Joined
Aug 9, 2007
Messages
23,470
Reaction score
4,667
Points
113
Location
woodhaven mi
Vehicle Year
1988
Make / Model
FORD mostly
Engine Type
V8
Engine Size
BIGGER
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
sawzall?
Tire Size
33-44
My credo
it is easier to fix and understand than "her"
typical on the tone ring for rust belt. since you yanked it may as well wire wheel it.

the shit steel the tone ring is made of rots like that when exposed to the air sitting for long periods.

hard to even find usable ttb parts these days. but 8.8 stuff is plentiful.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top