• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Replacing excluder dust seals: My How-to


stinkijeans

Member
Article Contributor
Joined
Feb 1, 2008
Messages
47
Reaction score
2
Points
8
Location
Oregon
Vehicle Year
2001
Make / Model
Ford
Engine Size
4.0 SOHC
Transmission
Automatic
Admins: Please sticky this if you feel it's worthy:
--------------

If you have one of these vehicles and you have a high-pitched squeal or whistling coming from the front axle, it’s a good bet your EXCLUDER seals are toast.

Ford TSB # 01-11-4

1998-2001 Explorer
2000, 2001 Ranger
2001 Explorer Sport Trac, Explorer Sport
1998-2001 Mountaineer

This TSB applies to 2001 Explorer Sport/Sport Trac 4X4 vehicles, 1998 - 2001 Explorer/Mountaineer 4X4 vehicles (all build dates), and 2000 - 2001 Ranger 4X4 vehicles built after 11/1/1999 only.

-----------------------


So what are these seals? Quite simply, they are a dust cover that sits behind your wheel hub. They are supposed to keep the dirt and grime from getting into your wheel bearing.
The wheel bearing itself is sealed, so I assume the dust shield is just an extra precaution.

Unfortunately, this seal is poorly designed and is prone to failure (in my opinion). The seal is NOT supposed to spin on the CV joint, however the way it is designed and attached to the CV joint, I don’t see how it will stay in place very long.
Once the seal breaks loose, you’ll get the ever-annoying squeal that sounds like your brakes are metal-to-metal.

These seals have failed 3 times on many Ranger and multiple times on other cars and it seems that Ford doesn't want to do anything about it.
Mine failed twice under warranty and now a third time. Since my extended warranty has expired… Ford told me ‘too-bad-so-sad’ and sent me packing.

Sound familiar?

I plan for a long fight with Ford. All they could say was ‘we’ll look into it’
Well, you can guess how long that’s going to take. In the meantime, I had to fix the seals myself. I wasn’t about to give the dealer or anyone else any more money.

I put together this guide in hopes that some of you DIY’ers can get an idea what you’re up against if you decide to do this on your own. I’ve done extensive searches on the Internet and haven’t found much in the way of pictures for the seal replacement. Even the manual is very vague.


· SAFETY FIRST! Be extremely careful working under cars. Please use the proper equipment such as jack stands, etc…
· REFER TO YOUR MANUAL!

I am by NO means an expert mechanic. I’m a backyard Joe just like many of you. If you pro’s out there have any advice or comments, please feel free to make them. I’m sure this guide isn’t going to be perfect!

------------

In this instance, I’m working with a 2001 Ford Ranger 4x4:


Parts used:

Seal: YL2Z-3K070-AA, Shield, Dust Qty. 2
Axle Nut: N808985-S100 Qty. 2
High Temperature grease


Special Tools used:

Front Hub removal/installer
32mm socket for axle nut






----------------

Loosen your axle nut before you take your tire off. It’s on there with over 160 ft. lbs., so it’s going to be a little fight.

CAUTION: Be extremely careful when raising your car and working under it. Use all precautions and fully secure it. Block your tires; use proper jack stands, etc… SAFETY FIRST!
The manual says to put your transmission in neutral, but I don't see how that applies in this repair. If anything, leaving it IN gear helped secure it from moving on you.

· Raise your car and remove your wheel. I supported the truck with a jack stand and used my floor jack under the A-arm.
I found having the jack under the A-arm with a little pressure helped when removing the ball joint and shock. You can easily move the arm up/down as needed with the jack.

· Remove the disc brake caliper anchor plate bolts.
On the first side of my truck, I removed the caliper, brake pads and THEN the anchor plate. You don't have to do this. You can remove it as an assembly once you remove the anchor bolts.

· Remove your caliper/anchor assembly and secure out of the way. Don’t let it hang by the brake hose. I tied mine out of the way with a piece of wire.

· Remove your brake rotor.
· Remove the axle nut (the manual says DO NOT reuse this ‘torque prevailing nut’) Buy a new one. The part number is shown above.
Ford didn't charge for this nut the last time they repaired the seals, so who knows if they replaced them or not. I did this time just to be sure.

Now it’s time to separate the axle from the hub using the hub puller. It won’t take much effort to separate the axle using the tool.




Once the axle is loose from the hub, remove the bolt that holds the upper ball joint to the wheel knuckle and separate it.
It's going to be a bit tight, so you might want a mallet to help free it from the control arm.
This is where the jack under the A-arm came in handy. I noticed if the A-arm was hanging free, it was hard to get the ball joint to come out. I found that if I jacked the A-arm up a bit and tap the upper control arm with a mallet, the ball joint popped loose.




Now comes a little bit of a fight:
You have to compress the CV joint so you can remove it from the hub and swing it out. I found this step to me a bit of a struggle, as it seems there isn’t enough room to clear the end of the CV joint. The manual doesn’t say anything about separating the tie rod; however after fighting the first side, I removed the tie rod on the second side.
It may even be easier if you separate the lower ball joint instead of the upper one. Maybe someone can comment on this if they’ve done it that way?

EDIT
: Thanks to Sasquatch's advice below, it is apparently easier to separate the lower ball joint. I'll do this the next time and get some pictures.









Ok, now with the axle out of the hub, it’s time to remove the CV joint.
The manual says to remove it with a special CV joint fork and slide hammer, but I didn't have one. I used a large screwdriver. Whatever you use, be careful not to damage the CV housing or your axle seal.

The manual also fails to mention that you need to move your shock out of the way. I couldn't get the CV boot past the shock. Now maybe that's because I'm using after-market Rancho shocks... I don't know. I didn't want to chance tearing up my CV boot, so I took the two lower screws off the shock and moved it over.

Once the CV shaft is popped loose, use BOTH hands when removing it from the axle housing. You don't want to damage that axle seal! I can only imagine what a pain in the *ss that would be to replace!



Now in case you’re wondering why you can’t simply install the new excluder seal without removing the CV shaft? Well… I suppose you could, but good luck getting it on correctly.
The seal is very thin and you could easily damage it if you don’t do it right. It’s A LOT easier taking the CV shaft out and putting it in a vice.


Ok, now you have everything out so it's time to CLEAN.
Pry off your old seal if it’s still on the CV shaft. One of mine was on the shaft, and the other wasn’t. Both were a nasty -gritty filthy mess.







Clean all the old grease and dirt from the CV shaft. I also used some emery cloth to clean up the seal surfaces and wash it off with brake cleaner.

Clean the back of the hub where the seal rides. Dig out all the old grease, dirt and grime. I even used Q-tips to get down inside the ring where the seal rides. It was also packed with old nasty grease and road grime. You don't want that to come back out and get into your new seals. Take your time and clean it thoroughly.




--------------

From what I’ve read… CLEANLINESS is vital in reinstalling these seals.
Make sure everything is spotless. Again, I used brake cleaner as it keeps the grease away and dries without any residue.


Once you have everything spick-n-span, it’s time to install that pesky seal on the CV shaft. You might want to skip that next beer until this part is done...




If you look close, you can see a metal ring in the seal (green arrow).
BE CAREFUL AND ONLY PRESS ON THAT STEEL AREA OF THE SEAL!
Otherwise you’ll damage it, then you’re out $20 plus the cost to go get a new one.

Start the seal by hand and then press on the steel part of the seal in equal amounts around the CV shaft. Take your time and be careful.
Ford has a special tool to install this seal, but since I didn’t have one, I used a couple of different things. I found that a 2” PVC coupler fit almost perfectly and only contacted the metal ring. I used that to get the seal most of the way down and then finished it off with small pin-punch. The seal will seat right up against that metal ring and be parallel to the CV joint face.








Whew! Ok, now that the hard part is out of the way, it’s time to lube it all up.
The manual says to ‘spread a 1/8 bead' of high-temp grease on the 'seal lips'.
Once again the manual was less than helpful and vague… which lips? The very outer edge, or the inside?

I went ahead and done both as I figured it wouldn’t hurt. If anything, the force of the shaft spinning should force the grease outwards:



------------------

Now that we’re all lubed up… time to reinstall.

The manual says to use a new C-clip each time the CV shaft is removed. I ended up ordering the wrong clip no thanks to the dealer, so I just reused my old ones. I will post the part number to the C-clip soon as I find out what it is.

Be careful when reinstalling the shaft. Use BOTH hands and be careful not to tear your axle seal!






-------------

Using the hub installer, pull the axle shaft into the hub:






Reinstall the axle nut and tighten as far as you can by hand. You’ll need to final torque once the tire is back on the ground.

Reinstall your upper ball joint, brake rotor, brake caliper, shock (if removed) and tie rod if removed).

Torque everything according to your manual.

For my 2001 Ranger, the toque specs are:

Nut and bolt retaining the upper ball joint: 41 ft. lb.
Front disc brake caliper anchor plate bolt: 85 ft. lb.
Disc brake caliper bolt: 24 ft. lb.
Hub nut/washer assembly: 162 ft. lb.
Wheel lugs: 90 ft. lb.

That's about it! :) It only took a few hours going slow.
If you're comfortable replacing a ball joint, or axle bearing, then this job shouldn't be too difficult for you.
I recommend getting the proper hub remover and installer tool. I bought the hub puller off EBay and it came with the installer tool.


------------------

In closing, it’s my goal to get Ford to recall their DEFECTIVE parts; however I fear it will be the same as fighting City Hall. It’s up to all of you that have this problem to let them know about it. In this case, it truly is “the squeaky wheel gets the grease”. Hopefully if enough of us complain, Ford will act.



SJ
 
Last edited:


Sasquatch_Ryda

Well-Known Member
Ford Technician
OTOTM Winner
Solid Axle Swap
Forum Staff - Retired
TRS Banner 2012-2015
Joined
Aug 8, 2007
Messages
7,916
Reaction score
108
Points
63
Age
36
Location
Terrace, BC, Canada
Vehicle Year
1991
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0L
Transmission
Automatic
2WD / 4WD
Solid Axle Swap 4x4
Tire Size
40s
It can be a bit of a paint to get the CV out of the hub without the lower ball joint removed, but it can be done. For what it takes to remove the knuckle completely I usually just undo the lower ball joint and remove it. Also you can usually just tap the CV shaft out of the hub with a hammer, or if it is seized in there good you can use an air hammer with a round nose punch to drift it through. As for installing it back into the hub you can just use the nut to pull it back in. I highly recommend lubing up the splines with good lube like Honey Goo to make disassembly the next time that much easier.

Very nice write up and good pictures tho, It will definitely help out out someone who is trying this for themselves for the first time. Good work.
 

stinkijeans

Member
Article Contributor
Joined
Feb 1, 2008
Messages
47
Reaction score
2
Points
8
Location
Oregon
Vehicle Year
2001
Make / Model
Ford
Engine Size
4.0 SOHC
Transmission
Automatic
Yes, Sasquatch... you're right... taking that lower joint off would have been a lot easier. I'll be sure to do that next time!

I'll edit my how-to as I get more suggestions.

Thanks for your input.


SJ
 

5lmustang

New Member
Joined
Dec 29, 2008
Messages
1
Reaction score
0
Points
0
Vehicle Year
1999
Make / Model
Ford
Engine Size
4.0L
Transmission
Manual
Does this apply to 99s as well?

I have a 1999 Ford Ranger 4x4 which has the same whistling sound coming from the from wheel on the passenger side. I know the 99s have different automatic hubs but does anyone know if they still have the excluder dust seals mentioned in this thread?

BTW - Great article!
 

green_duck42

New Member
Supporting Member
Joined
Feb 24, 2009
Messages
53
Reaction score
0
Points
0
Location
New Hampshire
Vehicle Year
1998
Make / Model
Ford
Engine Size
3.0
Transmission
Manual
how do you pull the seal into place if your CV shafts dont use an axle nut
 

ddiggerr

New Member
Joined
Aug 24, 2007
Messages
6
Reaction score
0
Points
0
Age
57
Transmission
Automatic
I know this post is old but ......

Excellent how-to. I have used this as a reference twice now, however, on my second replacement, the squeek remains. I am now pulling hair out as everything has been changed except one part.

Just wondering, would a bad hub assembly make the same exact squeek if it is going bad? This is all I can figure is making noise. Everything else is over greased just to be sure and the hub assemply is the only thing not changed.

Just don't want to spend $200 - $400 for the part, if squeek is still going to be there.
 

ddiggerr

New Member
Joined
Aug 24, 2007
Messages
6
Reaction score
0
Points
0
Age
57
Transmission
Automatic
Been a few months ...

Well its been a few months since I replaced dust seal. The squeek has never went away. Infact its gotten worse. It used to only sound off when I got around 40kmh, now its starts squeeking as soon as the wheels move and can even be heard at 100kmh.

Is it safe to just rip this seal out and trash it for good?:bawling:
 

ddiggerr

New Member
Joined
Aug 24, 2007
Messages
6
Reaction score
0
Points
0
Age
57
Transmission
Automatic
Couldn't wait

Didn't get any replies so I ripped that bugger out of there and guess what. Sound is worse than before. As in louder. Obviously the dust seal is not the cause of the squeeking, so that brings me back to the original question.

Would a worn out hub assembly make the same tye of squeeking. Does not increase or decrease with speed, or when turning, in 4x4 or not, or when braking. Its a consistant squeek from to finish.

:annoyed:
 

ddiggerr

New Member
Joined
Aug 24, 2007
Messages
6
Reaction score
0
Points
0
Age
57
Transmission
Automatic
Pulling hair out and not much left!!

Ok to date I have removed dust seal, replaced both wheel hub assemblies, new break pads and squeek is still there.

It squeeks the same at 1kmh as it does at 50+kmh. It squeeks in reverse, while breaking and even coasting down the road with engine off.

I have tore into it several times and made sure there is nothing rubbing, stuck, or dirty. The only time it doesn't squeek is when its raining out when driving.

Time to throw in the white towel and pay hundreds of dollars to have a shop repeat everything I did myself.

Unless theres something I have missed.
:icon_twisted:
 

gw33gp

Well-Known Member
U.S. Military - Veteran
TRS Banner 2010-2011
Ham Radio Operator
Joined
Aug 7, 2007
Messages
1,728
Reaction score
531
Points
113
Location
Costa Mesa, CA
Vehicle Year
2002
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0 SOHC
Transmission
Manual
2WD / 4WD
4WD
Tire Size
33"
I know this is an old thread, but I want to update it because it is one of the very few places I could find information on the excluder seal. I found one other thread that indicated part number YL2Z-3K070-AA would fit an 02 Ranger. I also got information from many dealers that it would not fit my 02. I had a couple Ford dealers tell me that the original part for my 02 was superseded to YL2Z-3K070-AA. So, I decided to buy one hoping it would fit.

Yes, it does fit my 02. I ended up finding another so I would have one have when I replace my other front hub. I can also tell you, they have been discontinued, but there are still a few out there if you are willing to do an extensive search.

I can almost guarantee your's are bad if you have an 02 4WD Ranger or earlier. Mine were in two pieces and had been that way for a while. They are probably bad on later Rangers too but I don't know if YL2Z-3K070-AA will fit later Rangers. The good news is if you don't do a lot of off-road travels, you probably don't need them.

I can add to the above information regarding installation. It is much easier to do the work if you disconnect the lower and upper ball joints. The tie rod does not have to be disconnected. I was also able to do the installation without removing the CV joint. I made a tool that allowed me to install the excluder seal with the CV joint in place. I have attached a photo showing the tool on the axle after installing the excluder seal.

Excluder seal 1.JPG


You can see the grease on the seal. I had already put the grease on the seal before I remembered I wanted to take a photo of the tool in place. Not a problem though, the grease is pretty much outside the area where the tool contacts the seal.

I thought the seal lip would ride on the hub but once it was apart, I realized it contacts a flange inside the spindle. I cleaned up the contact face of the flange very well with fine sandpaper with a final clean up with 1000 grit to make sure it was a smooth surface. I also left a thin film of lube on it.

So far it is working great, but I have not put a lot of miles on it.
 
Last edited:

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top