• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Just installed a 4in roughcountry lift need help


That_4.0_ranger

Active Member
Joined
Nov 19, 2021
Messages
235
Reaction score
152
Points
43
Location
Appleton,W.A.
Vehicle Year
1991,1987
Make / Model
Ford Ranger
Engine Size
4.0, 2.9
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
stock
Tire Size
31x10.50-15
So i recently installed a 4in rough country lift kit with new rear leaf springs and im having an issue that whenever i take off no matter what it has a really bad shake throughout the whole truck but it goes away after a couple seconds. It is in the rear somewhere cant quite figure it out. Hope a certain @bobbywalter could help. Thanks in advance
 


Sloryd66

Active Member
Joined
Mar 28, 2022
Messages
68
Reaction score
99
Points
33
Location
Orlando, FL
Vehicle Year
1999
Make / Model
Mazda B2500
Engine Type
2.5 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
4" Wulf
Tire Size
265/65/17
My credo
If I learned from my mistakes, I'd be a genius !!
Sounds like the driveline angle on the diff may be incorrect now and putting more stress on the u-joints. But you mentioned it goes away after a few seconds? I had a Jeep Cherokee that did that after a lift and dropping the trans cross member an inch solved the vibration…but mine was felt all the time before doing that.
 

That_4.0_ranger

Active Member
Joined
Nov 19, 2021
Messages
235
Reaction score
152
Points
43
Location
Appleton,W.A.
Vehicle Year
1991,1987
Make / Model
Ford Ranger
Engine Size
4.0, 2.9
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
stock
Tire Size
31x10.50-15
Thats what i was thinking but the new springs have a shim in them so it changes the angle for the diff so that shouldn't happen but idk
 

dvdswan

Well-Known Member
U.S. Military - Veteran
Joined
Feb 11, 2021
Messages
2,832
Reaction score
2,899
Points
113
Location
Seattle, WA
Vehicle Year
1991
Make / Model
Ranger XLT 2WD
Engine Type
3.0 V6
Transmission
Automatic
2WD / 4WD
2WD
My credo
Keep your mind like an umbrella, it only works if its open... Continually learning.
Lube the slip joint in the driveline as well as the u-joints... If its possible. U-joints are old and dry and the slip joint is just dry. I'd try that first.
 

Bgunner

Well-Known Member
Supporting Member
Joined
May 14, 2018
Messages
1,755
Reaction score
1,039
Points
113
Location
Western Mass.
Vehicle Year
1994
Make / Model
Ford/Ranger XLT
Engine Type
3.0 V6
Transmission
Manual
2WD / 4WD
2WD
Tire Size
225/70/R15
My credo
If it's not broken Don't Fix It!
Does yours have a carrier bearing on the drive shaft?

When carrier bearings go they give one heck of a vibration on take off then smooth out but howl at high speeds. Mine howled when I got near 70 mph as an example.
 

scotts90ranger

Well-Known Member
RBV's on Boost
Joined
Feb 28, 2001
Messages
7,936
Reaction score
4,231
Points
113
Location
Dayton Oregon
Vehicle Year
1990, 1997
Make / Model
Ford
Engine Type
2.3 (4 Cylinder)
Engine Size
2.3 Turbo
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6
Tire Size
35"
Carrier bearing is likely the issue, if it wasn't lowered with the lift it's angles are probably goofy and making it mad...
 

That_4.0_ranger

Active Member
Joined
Nov 19, 2021
Messages
235
Reaction score
152
Points
43
Location
Appleton,W.A.
Vehicle Year
1991,1987
Make / Model
Ford Ranger
Engine Size
4.0, 2.9
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
stock
Tire Size
31x10.50-15
Does yours have a carrier bearing on the drive shaft?

When carrier bearings go they give one heck of a vibration on take off then smooth out but howl at high speeds. Mine howled when I got near 70 mph as an example.
Its hard to hear anything else making nose over the sound of my exhaust
 

That_4.0_ranger

Active Member
Joined
Nov 19, 2021
Messages
235
Reaction score
152
Points
43
Location
Appleton,W.A.
Vehicle Year
1991,1987
Make / Model
Ford Ranger
Engine Size
4.0, 2.9
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
stock
Tire Size
31x10.50-15
Carrier bearing is likely the issue, if it wasn't lowered with the lift it's angles are probably goofy and making it mad...
How would i go about lowering it?
 

scotts90ranger

Well-Known Member
RBV's on Boost
Joined
Feb 28, 2001
Messages
7,936
Reaction score
4,231
Points
113
Location
Dayton Oregon
Vehicle Year
1990, 1997
Make / Model
Ford
Engine Type
2.3 (4 Cylinder)
Engine Size
2.3 Turbo
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6
Tire Size
35"
My F350 had a piece of 1" square tubing between the crossmember and the carrier bearing, there's only two bolts holding it up... they sell a spacer I'm pretty sure but just space it down...
 

That_4.0_ranger

Active Member
Joined
Nov 19, 2021
Messages
235
Reaction score
152
Points
43
Location
Appleton,W.A.
Vehicle Year
1991,1987
Make / Model
Ford Ranger
Engine Size
4.0, 2.9
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
stock
Tire Size
31x10.50-15
My F350 had a piece of 1" square tubing between the crossmember and the carrier bearing, there's only two bolts holding it up... they sell a spacer I'm pretty sure but just space it down...
Yea i thought that's ho mine would be judging by my buddies Toyota witch hangs down but mine is bolted directly to the crossmember so to lower it you have to lower the whole crossmember
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,872
Reaction score
5,031
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
Yea i thought that's ho mine would be judging by my buddies Toyota witch hangs down but mine is bolted directly to the crossmember so to lower it you have to lower the whole crossmember
Longer bolts and spacers?
 

SenorNoob

Well-Known Member
TRS Event Participant
Joined
Oct 24, 2012
Messages
2,348
Reaction score
520
Points
113
Location
Middle Tennessee
Vehicle Year
1988
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Total Lift
1.5" Front + 4" Rear
Tire Size
245-70-R16
The crossmember was riveted on my truck. So cut apart, then spacers and bolts as needed.
 

Sponsored Ad


Sponsored Ad

Members online

No members online now.

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top