• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

high and low beams AT ONCE!


Brian1973

Member
Joined
May 29, 2010
Messages
129
Reaction score
0
Points
16
Location
Cincinnati, OH
Vehicle Year
1991
Make / Model
Ford
Transmission
Manual
1991 Ranger. If headlights are on and I push the stick forward (towards dashboard), I get high beams (while simultaneously the low beams switch off). I find it more to my liking to just pull the stick back and I keep my low beams working while my high beams add to the illumination! It's brighter! Problem is as we all know, the stick doesn't stay pulled back automatically. I guess this is just so it is easy to flash your lights if you need to. Albeit helpful.

Just wondering if anyone has thought of a way to keep those low beams on while pushing the stick forward into the locked high beam position? And is that electrically ok to do? Seems to work fine when I push the stick towards me and hold it.
 


RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,291
Reaction score
8,294
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
Heat from both filaments being on will shorten life of the bulb, which is why it is setup as "flash to pass", a momentary activation.

You could setup a relay(5 post 30amp) at each head light that would be activated by high beam power, and then pass fused(20amp) power to low beams.
5 post so you don't back feed that fused power to multi-function switch
 

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
I would highly recommend not doing that. If you feel you need more light there are three things I would do as an alternative to running your headlights on an over-load setting that will drastically shorten the bulb life and speed up glazing the lenses.

1) Clean the lenses so they are clear, not fogged.
2) Invest in brighter bulbs. A blue tinted glass will give a whiter beam.
3) Go see an optometrist and get your night vision tested.
 

hoosier1104

I'm Awesome!
Supporting Member
U.S. Military - Veteran
V8 Engine Swap
MTOTM Winner
TRS Banner 2010-2011
TRS Banner 2012-2015
Joined
Jul 17, 2009
Messages
5,123
Reaction score
104
Points
0
Location
Camby, IN
Vehicle Year
1999
Make / Model
Ford
Engine Size
302 based goodness
Transmission
Automatic
My credo
Work hard and play harder
^What he said.
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,197
Reaction score
17,507
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
Some older Fords didn't have the greatest light switches either, I know first gens left a lot to be desired for durability (mainly causing fires)... not sure if second gens are a lot better.
 

hoosier1104

I'm Awesome!
Supporting Member
U.S. Military - Veteran
V8 Engine Swap
MTOTM Winner
TRS Banner 2010-2011
TRS Banner 2012-2015
Joined
Jul 17, 2009
Messages
5,123
Reaction score
104
Points
0
Location
Camby, IN
Vehicle Year
1999
Make / Model
Ford
Engine Size
302 based goodness
Transmission
Automatic
My credo
Work hard and play harder
Overloading a circuit is NO BUENO. DO NOT DO IT!!!! Buy some fog lights or a LED light bar before doing that. DO NOT DO IT!!!!
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,868
Reaction score
5,029
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
Nobody recommended overloading the circuit. RonD said the OP could add a switch [relay] that would allow battery power to run the low-beam while the high beam is on.
 

4x4junkie

Forum Staff Member
TRS Forum Moderator
TRS 20th Anniversary
Joined
Aug 19, 2001
Messages
10,749
Reaction score
580
Points
113
Location
So. Calif (SFV)
Vehicle Year
1990
Make / Model
Bronco II
Engine Type
2.9 V6
Engine Size
2.9L V6
Transmission
Manual
2WD / 4WD
4WD
Tire Size
35x12.50R15
2) ... A blue tinted glass will give a whiter beam.
Bad idea if one is looking for more light... Blue tinting is a filter that reduces the light output. And if that isn't bad enough, it's removing the parts of the light spectrum that the human eye is most sensitive to (520-580nm & longer), while leaving the part of the spectrum that causes more glare (400-480nm).

Higher-wattage clear bulbs would be a better option, however that still could potentially open the door to overheating problems in the wiring & light switch contacts. Rewiring the lights so they are powered through a lighting relay like mentioned earlier could help alleviate such concerns, and the resulting higher voltage to the bulbs would do much more to produce a brighter whiter light than any blue filter can.

By far the best option for more light is to add a set of auxiliary driving lights.
There are many options available in driving lights, though I would probably suggest avoid anything LED if glare is a concern.
 

Doofy

Member
Supporting Member
U.S. Military - Veteran
Joined
Jul 27, 2008
Messages
947
Reaction score
6
Points
18
Location
Alaska
Vehicle Year
1998
Make / Model
Ford
Engine Size
3.0
Transmission
Manual
My credo
Shit Happens...Then You Die.
Yes x 2 on adding auxiliary lighting with the proper fusing and relays. Automotive wiring is puny to begin with and just deteriorates more over time.
 

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
Nobody recommended overloading the circuit. RonD said the OP could add a switch [relay] that would allow battery power to run the low-beam while the high beam is on.
Right, RonD's method would potentially reduce power flow through the switch, which is a good thing, but as Ron also pointed out, it is going to drastically increase the amount of heat output. That is the big thing to be avoided here.
 

tinman_72

Active Member
Joined
Apr 14, 2008
Messages
529
Reaction score
136
Points
43
Location
North Georgia
Vehicle Year
1993
Make / Model
Ford
Engine Type
2.5 (4 Cylinder)
Engine Size
2.5
Transmission
Manual
2WD / 4WD
2WD
Total Lift
Factory
Total Drop
None
Tire Size
255/60R15
My credo
RoHS compliant
I installed two relays in my '93 Ranger, one for the low beam and one for the high beam. I installed them using the wires from the multi-function switch as the "switch" and ran power directly from the battery, through fuses and the relays to the headlights. This had more effect than when I replaced the glazed headlight assemblies with brand new pieces.
 

Brian1973

Member
Joined
May 29, 2010
Messages
129
Reaction score
0
Points
16
Location
Cincinnati, OH
Vehicle Year
1991
Make / Model
Ford
Transmission
Manual
Last edited:

lil_Blue_Ford

Well-Known Member
TRS Forum Moderator
Supporting Member
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
8,208
Reaction score
5,963
Points
113
Location
Butler, PA, USSA
Vehicle Year
95
Make / Model
Ford
Engine Size
4.9L
Transmission
Manual
LED headlight bulbs generate a bit of heat, most of the high power ones have heat sinks and or fans. But, you can find LED headlight bulbs that put out more light than factory bulbs.


Sent from my kite using a trebuchet
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,197
Reaction score
17,507
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
When I was talking about heating with the switch it was because you are basically running 2x the voltage the light switch normally sees thru the switch when you hold the lever back.

My pending brother in law put LED's in his Sport Trac... supposed to be good ones and he is happy. I am not overly positive they are much better than the sealed beam halogens in my '85. Pretty sure the OEM bulbs in my '02 F-150 put out more light in better places.

Sealed beam replacements are literally night and day vs a halogen though. And maybe it is just what he got too.
 
Last edited:

Mark_88

Well-Known Member
Joined
Aug 11, 2007
Messages
18,554
Reaction score
240
Points
63
Age
68
Location
Ontario, Canada
Vehicle Year
2007
Make / Model
Dordge
Engine Size
3.3 Fuel Injected
Transmission
Automatic
My credo
Love Thy Neighbor
I agree with adding extra lights and cleaning the lenses.

My 92 lenses were fogged so bad I was tempted to replace them with new lenses. Then I found a method on-line to clean them and it made a huge difference.

https://www.youtube.com/watch?v=y0gbr7YdWLU
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top