• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Frame rivets to bolts


Rex2nr

New Member
Joined
Aug 16, 2015
Messages
79
Reaction score
1
Points
0
Location
Rochester, NY
Vehicle Year
1999
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
What size bolts do you guys use when replacing riveted frame parts? I need to replace the crossmember above the fuel tank on my 99. I know grade 8, assuming somewhere between 3/8 and 1/2", 1-1/2" long? How tight should they be? 100ft/lb or 3/4" drive impact tight?
 


ratdude747

Member
Supporting Member
Article Contributor
TRS 20th Anniversary
Joined
Aug 10, 2014
Messages
503
Reaction score
22
Points
18
Age
31
Location
Madison, IN
Vehicle Year
1995
Make / Model
Ford Ranger
Engine Type
4.0 V6
Engine Size
4.0L
Transmission
Automatic
2WD / 4WD
2WD
Tire Size
215/70R15
What size bolts do you guys use when replacing riveted frame parts? I need to replace the crossmember above the fuel tank on my 99. I know grade 8, assuming somewhere between 3/8 and 1/2", 1-1/2" long? How tight should they be? 100ft/lb or 3/4" drive impact tight?
Size depends on the rivet. I've used a few different sizes... 5/16" IIRC was one of them.

Torque? I use the German spec of Gutentight (good 'n tight). They're grade 8 so unless you do something really dumb you'll be fine.
 

Rex2nr

New Member
Joined
Aug 16, 2015
Messages
79
Reaction score
1
Points
0
Location
Rochester, NY
Vehicle Year
1999
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
I was just wondering because the rivets allowed some flex, so I was wondering if they should be loose enough to allow the rails/crossmember to flex but obviously still tight.
 

ratdude747

Member
Supporting Member
Article Contributor
TRS 20th Anniversary
Joined
Aug 10, 2014
Messages
503
Reaction score
22
Points
18
Age
31
Location
Madison, IN
Vehicle Year
1995
Make / Model
Ford Ranger
Engine Type
4.0 V6
Engine Size
4.0L
Transmission
Automatic
2WD / 4WD
2WD
Tire Size
215/70R15
I was just wondering because the rivets allowed some flex, so I was wondering if they should be loose enough to allow the rails/crossmember to flex but obviously still tight.
Biggest size that fits. The rivets are form fitting so you you will want to match the size.
 

Mark_88

Well-Known Member
Joined
Aug 11, 2007
Messages
18,554
Reaction score
240
Points
63
Age
68
Location
Ontario, Canada
Vehicle Year
2007
Make / Model
Dordge
Engine Size
3.3 Fuel Injected
Transmission
Automatic
My credo
Love Thy Neighbor
I ground off the rivets on my spring supports and there was zero clearance on them...so I would find a bolt that is exactly the size of the hole...movement in support to me would be a bad thing...but, then again, I'm not a structural engineer...so I know zero about it other than I usually replace what I remove with something the same size because that's the way it was designed.
 

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
On my current project I am finding that on 90% of the holes 7/16 bolts are not quite big enough, 1/2" don't quite fit. I have been punching the holes out to 1/2" because I am removing minimal material to make them fit, some of the holes are actually 1/2, and I only wanted to deal with buying one size of bolt.

Grade 5 is acceptable for frame repairs, but I am also using grade 8, with stover lock nuts. 100 ft/lb should be good enough, but I am going to 1/2" impact tight. I'm pretty sure a 3/4" impact will break the bolts.
 

kunar

Forum Staff Member
TRS Forum Moderator
Supporting Member
Article Contributor
V8 Engine Swap
Joined
Jun 10, 2003
Messages
4,158
Reaction score
131
Points
63
Age
36
Location
Toledo, Ohio
Vehicle Year
1987
Make / Model
Ford
Engine Type
V8
Engine Size
5.8l
Transmission
Manual
2WD / 4WD
2WD
On my current project I am finding that on 90% of the holes 7/16 bolts are not quite big enough, 1/2" don't quite fit. I have been punching the holes out to 1/2" because I am removing minimal material to make them fit, some of the holes are actually 1/2, and I only wanted to deal with buying one size of bolt.

Grade 5 is acceptable for frame repairs, but I am also using grade 8, with stover lock nuts. 100 ft/lb should be good enough, but I am going to 1/2" impact tight. I'm pretty sure a 3/4" impact will break the bolts.
good info here. i believe they are probably 12mm from the factory. drill them out to 1/2" so a 1/2" bolt fits snug. they need to be tight. 100 ft/lb should be good for a 1/2" bolt.
 

chvlfrk

December 2010 STOTM Winner
U.S. Military - Veteran
V8 Engine Swap
MTOTM Winner
Joined
Aug 9, 2007
Messages
1,168
Reaction score
31
Points
48
Age
65
Location
Niota, TN
Vehicle Year
98
Make / Model
Ranger XLT 5.0L
Engine Type
V8
Engine Size
5.0L
Transmission
Automatic
Tire Size
235/70R15 front / 275/60R15 rear
My 02.....

Torque? I use the German spec of Gutentight (good 'n tight). They're grade 8 so unless you do something really dumb you'll be fine.
==============
Use this QUITE FREQUENTLY myself on all my projects!


Grade 5 is acceptable for frame repairs, but I am also using grade 8, with stover lock nuts. 100 ft/lb should be good enough, but I am going to 1/2" impact tight. I'm pretty sure a 3/4" impact will break the bolts.
=============
I also use 1/2" impact & Grade 8 hardware .........if your worried bout them backing out, spot weld the bolt heads, then if the nuts loosen there is no way for it to come completely apart.

Have also heard of guys using carriage bolts & spot welded them to frame.
 

adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
good info here. i believe they are probably 12mm from the factory. drill them out to 1/2" so a 1/2" bolt fits snug. they need to be tight. 100 ft/lb should be good for a 1/2" bolt.
I agree, they were probably 12mm originally. 7/16" is 11mm, and as I said 1/2" didn't quite fit. As I said, the amount of material I was removing was minimal.

I also use 1/2" impact & Grade 8 hardware .........if your worried bout them backing out, spot weld the bolt heads, then if the nuts loosen there is no way for it to come completely apart.

Have also heard of guys using carriage bolts & spot welded them to frame.[/B]
That's a good idea. Here in PA steel lock nuts, not nylon and no lock washers, are required to be used when replacing frame rivets. I'd but using lock nuts anyway. I am probably going to be putting red thread locker on too.

I was actually using the drill bit one size under 1/2, 30/64 or 15/32, not sure, can't read the side anymore, because my 1/2" was MIA. It was enough that the bolts fit, but they were cutting threads in the hole, so I would make the bolts tight in the holes (and since the threads got cut through both pieces at the same time they match) and then run the nut down over the other side.
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,870
Reaction score
5,030
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
I drill to 1/2" using a step drill bit because the step bit gives a round hole where a normal bit can give a triangular hole, and is much easier to drill with into a hole already close to the size you want. I use a Grade 8 bolt that has a shoulder that will touch throughout the hole. I then use hardened [grade 8] flat washers under the head and under the nut to build out enough that the steel lock nuts will not hit the shoulder [un-threaded portion of the shank]. I do this because you lose strength in shear where there are threads.

I've also used 7/16" bolts but they are harder to come by.
 

AllanD

TRS Technical Staff
TRS Technical Advisor
Joined
Jun 1, 2001
Messages
7,897
Reaction score
134
Points
63
Age
62
Location
East-Central Pennsylvania
Vehicle Year
1987... sorta
Make / Model
Ford
Engine Size
'93 4.0
Transmission
Manual
The rivets expand to fill the holes as they are heated to the plastic range of the metal for installation...

I find that generally 7/16-20 fine thread bolts work well in most locations, but in those situations where I choose to use 1/2" bolts I do nor Drill or ream the holes...

I run a 1/2"-20 "fine thread" tap through the holes then run the bolt in snugly
then hold it in place while I tighten a self-locking nut onto the other side

I have replaced most of the rivets on my truck with bolts, and plan eventually to replace them all...

AD
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,870
Reaction score
5,030
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
I run a 1/2"-20 "fine thread" tap through the holes then run the bolt in snugly
then hold it in place while I tighten a self-locking nut onto the other side

AD
This is the only time that I have to dis-agree with AllenD. If the two pieces are not in contact with each other when tapping, there will be a vast amount of stress on the bolt and with no friction between the two pieces the hole could egg out over time. If you can clamp the two pieces together while tapping then it should be OK. Drilling and using the shank shoulder to fill the hole is easier and as strong, if not stronger IMO.
 

Mac

Well-Known Member
Supporting Member
V8 Engine Swap
Joined
Aug 9, 2007
Messages
5,103
Reaction score
182
Points
63
Age
77
Location
C. Wisconsin
Vehicle Year
2003
2000
199
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
General thread torque ratings and allowable loads for various sizes. 7/16-14 Gr 5 torqued to 50 ft-lbs and 7/16-20 torqued to 70 ft-lbs. Load on those with safety factor is 1580 lbs and 2255 lbs. 1/2-13 Gr 5 torqued to 75 ft-lbs and 1/2-20 Gr 8 torqued to 100 ft-lbs. Loads on those is 2060 lbs and 2950 lbs. Torque values for dry threads. Structural steel never uses lock nuts.
Dave - 45 years as mechanical designer
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,870
Reaction score
5,030
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
General thread torque ratings and allowable loads for various sizes. 7/16-14 Gr 5 torqued to 50 ft-lbs and 7/16-20 torqued to 70 ft-lbs. Load on those with safety factor is 1580 lbs and 2255 lbs. 1/2-13 Gr 5 torqued to 75 ft-lbs and 1/2-20 Gr 8 torqued to 100 ft-lbs. Loads on those is 2060 lbs and 2950 lbs. Torque values for dry threads. Structural steel never uses lock nuts.
Dave - 45 years as mechanical designer
Thanks for the input.

Structural steel never uses lock nuts.
Does structural steel have the same vibrations and torque put through the main beams? I've seen pics and I'm sure that anyone that drives over potholes has twisted the frame in their truck. I believe that's why everyone uses lock nuts. Do lock washers provide the same clamping force as lock nuts? Maybe better to use lock washers because of spring pressure? Or are you suggesting no lock system of any sort? Inquiring minds need to know....
TIA.
 

Mark_88

Well-Known Member
Joined
Aug 11, 2007
Messages
18,554
Reaction score
240
Points
63
Age
68
Location
Ontario, Canada
Vehicle Year
2007
Make / Model
Dordge
Engine Size
3.3 Fuel Injected
Transmission
Automatic
My credo
Love Thy Neighbor
General thread torque ratings and allowable loads for various sizes. 7/16-14 Gr 5 torqued to 50 ft-lbs and 7/16-20 torqued to 70 ft-lbs. Load on those with safety factor is 1580 lbs and 2255 lbs. 1/2-13 Gr 5 torqued to 75 ft-lbs and 1/2-20 Gr 8 torqued to 100 ft-lbs. Loads on those is 2060 lbs and 2950 lbs. Torque values for dry threads. Structural steel never uses lock nuts.
Dave - 45 years as mechanical designer
Good info...thanks...

What about lock washers? I've often used those instead of lock nuts and have found many on automotive applications...just can't remember where or when.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top