• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Drill bits


rumblecloud

Well-Known Member
Supporting Member
Joined
Mar 6, 2020
Messages
1,385
Reaction score
1,106
Points
113
Location
48022
Vehicle Year
1994
Make / Model
Ranger Splash
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
1-1/2 inch front leveling
Total Drop
Stock
Tire Size
31/10.50/15
My credo
What's the worst that could happen?
Ok, what do you do with them when they get dull?

Just going thru a recent battle drilling out the end of a pinch bolt that I had to cut the head off. I must've gone thru six different bits because they dulled so fast. I'm not talking about cheap ass bits. 15 to 18 bucks a piece. Some I had but three were brand spanking new.

But my question is what do I do with them now? Can they be resharpened? Drill Doctor?
And I have coffe can full of older bits that virtually useless. I know I'm not alone.

So what do you do with yours?
 


duffy

Member
Joined
Sep 26, 2020
Messages
96
Reaction score
19
Points
8
Location
Hot Springs, SD
Vehicle Year
1989
Make / Model
Ford Bronco II
Transmission
Automatic
I bought a Drill Doctor when they first came out and every so often (once every couple of years) I get tired of dull bits and break it out.
 

CrabGuy

Well-Known Member
Supporting Member
U.S. Military - Veteran
Joined
Feb 24, 2021
Messages
333
Reaction score
470
Points
63
Location
Sacramento, CA/Seal Rock, OR
Vehicle Year
2004-Bone stock
Make / Model
Ranger XLT
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
My credo
Why should I pay someone else to screw it up when I can screw it up myself for free?
I have had good luck with my Drill Doctor 750X but seem to have better results on my older black oxide machinist grade bits than the common titanium coated bit sets so common today. Those will sharpen OK but seem more speed sensitive as to how long they stay sharpened. The older original Drill Doctor was terrible and mine was tossed.
 
Last edited:

Roert42

Well-Known Member
RBV's on Boost
TRS Event Participant
Joined
Apr 24, 2020
Messages
4,739
Reaction score
4,891
Points
113
Location
Kintersville, PA
Vehicle Year
2011
Make / Model
Ranger XLT
Engine Size
4.0 SOHC
Transmission
Automatic
2WD / 4WD
2WD
I sharpen them on a bench grinder.

I do a lot of drilling through stainless at work, that dulls them out pretty fast, so I got decent at it. Look at a new drill bit, then use the grinder to reshape the edge to look like a new drill bit. The nice thing about doing it by hand is you can put different angles on the bit depending on what kind of material you need to drill. A steeper angle is good for harder materials because it bites less, a wide angle can be nice for aluminum because you will remove more material faster.

We have a drill doctor at the shop, but I could never get it to actually sharpen the dill bits. Puts a nice straight edge on it, look good, but not actually sharp.
 

rusty ol ranger

Im a Jeep guy now.
Supporting Member
Joined
Sep 22, 2007
Messages
12,269
Reaction score
7,278
Points
113
Location
Michigan
Vehicle Year
1987
Make / Model
Ford
Engine Type
2.9 V6
Engine Size
177 CID
Transmission
Manual
2WD / 4WD
2WD
My credo
A legend to the old man, a hero to the child...
I bought an old black and decker sharpner from the restore last summer...paid 5 bucks and put it to work. Saved me a fourtune over buying new bits
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,872
Reaction score
5,031
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
You tube....
And a bench grinder.
 

rumblecloud

Well-Known Member
Supporting Member
Joined
Mar 6, 2020
Messages
1,385
Reaction score
1,106
Points
113
Location
48022
Vehicle Year
1994
Make / Model
Ranger Splash
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
1-1/2 inch front leveling
Total Drop
Stock
Tire Size
31/10.50/15
My credo
What's the worst that could happen?

Shran

Junk Collector
TRS Forum Moderator
Supporting Member
Article Contributor
V8 Engine Swap
Solid Axle Swap
Joined
Mar 4, 2008
Messages
8,637
Reaction score
4,704
Points
113
Location
Rapid City SD
Engine Type
V8
Engine Size
5.0
I sharpen everything bigger than 1/4" or so on an angle grinder with a flap wheel. Sometimes I use the bench grinder first for big bits that are really trashed, then hit them with the flap wheel. That usually gets them nice and sharp. Smaller bits are usually cheap enough to throw away although I do try on occasion.

I have a drill doctor but I haven't used it in years. Not sure why but it would get certain bits perfect and totally ruin others so I quit using it.
 

rumblecloud

Well-Known Member
Supporting Member
Joined
Mar 6, 2020
Messages
1,385
Reaction score
1,106
Points
113
Location
48022
Vehicle Year
1994
Make / Model
Ranger Splash
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
1-1/2 inch front leveling
Total Drop
Stock
Tire Size
31/10.50/15
My credo
What's the worst that could happen?
Well then...if anyone's looking for me, I'll be in the barn for the next week sharpening drill pits and getting anal putting all the sets back together 😬
 

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,214
Reaction score
16,350
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.
I tried a drill Dr once, over 20 years ago. Results weren't great. I do big bits on the bench grinder and replace small bits.
 

DILLARD000

Well-Known Member
Joined
Sep 25, 2020
Messages
877
Reaction score
652
Points
93
Location
Earth
Vehicle Year
2001 Ford
Make / Model
SportTracJob2
Engine Size
V6~4.0L~SOHC
Transmission
Automatic
2WD / 4WD
4WD
...tried a drill Dr once, over 20 years ago. Results weren't great
...do big bits on the bench grinder and replace small bits.
Same here, threw DrillDr in the trash after a few tries & choice words.
BenchGrinder & a little patience.
 

Roert42

Well-Known Member
RBV's on Boost
TRS Event Participant
Joined
Apr 24, 2020
Messages
4,739
Reaction score
4,891
Points
113
Location
Kintersville, PA
Vehicle Year
2011
Make / Model
Ranger XLT
Engine Size
4.0 SOHC
Transmission
Automatic
2WD / 4WD
2WD
Yeah, those small bits are a giant pita to sharpen. Just toss them away.
 

scotts90ranger

Well-Known Member
RBV's on Boost
Joined
Feb 28, 2001
Messages
7,936
Reaction score
4,231
Points
113
Location
Dayton Oregon
Vehicle Year
1990, 1997
Make / Model
Ford
Engine Type
2.3 (4 Cylinder)
Engine Size
2.3 Turbo
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6
Tire Size
35"
drill doctor relies on the spiral cut being at the same angle, so bits with a different angle will sharpen differently, that's why it's a pain...

I have a mini bench grinder I usually at home, the 3" harbor freight deal with the flex wand, it's gutless unless fully wound up but it does a good job on some things...
 

PetroleumJunkie412

Official TRS EV Taunter
Supporting Member
TRS 20th Anniversary
TRS Event Participant
Joined
Oct 31, 2018
Messages
7,826
Reaction score
6,565
Points
113
Location
Dirtman's Basement
Vehicle Year
1988
Make / Model
Ranger
Engine Size
2.9l Trinity
Transmission
Manual
2WD / 4WD
4WD
My credo
Give 'yer balls a tug. Fight me.
Well then...if anyone's looking for me, I'll be in the barn for the next week getting anal 😬
Everything you say will be misquoted and used against you.
 

RumPunch

Well-Known Member
Supporting Member
Law Enforcement
Joined
Jan 12, 2021
Messages
779
Reaction score
827
Points
93
Location
Walkerton Va 23177
Vehicle Year
1988
Make / Model
Ford Bronco II
Engine Type
2.9 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
3"
Tire Size
31x10.50R15
Mac drill bits warranty if chipped. Gets past 2 sharpenings vice, hammer, exchange
 

Sponsored Ad


Sponsored Ad

Staff online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top