• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

crank but no spark after engine swap


Angie

Well-Known Member
V8 Engine Swap
Joined
May 18, 2008
Messages
1,510
Reaction score
368
Points
83
Location
Vancouver area BC Canada
Vehicle Year
92 & 83 project
Make / Model
Ford
Engine Type
V8
Engine Size
4.0L 302
Transmission
Automatic
glad to hear you are making progress. this is what i was thinking, something isn't plugged in or you may have over looked something. as ron said, these engines are fairly basic in the spark no spark. cheers and happy hunting.
 


alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,870
Reaction score
5,030
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
I had a problem with no spark. After several months of sporadic detective work, I found one of the plugs not making proper connection. Turns out the little orange rubber o-ring inside the connector was preventing full connection. A little dielectric grease cured that...
 

sam klassen

New Member
Joined
Dec 6, 2022
Messages
22
Reaction score
3
Points
3
Location
canada
Vehicle Year
1994
Make / Model
ford ranger
Transmission
Automatic
I had a problem with no spark. After several months of sporadic detective work, I found one of the plugs not making proper connection. Turns out the little orange rubber o-ring inside the connector was preventing full connection. A little dielectric grease cured that...
That's the orange oring in the connector to the coil?
And dielectric greace gives a better connection?
 

alwaysFlOoReD

Forum Staff Member
TRS Forum Moderator
TRS Banner 2012-2015
TRS 20th Anniversary
Joined
Apr 13, 2009
Messages
13,870
Reaction score
5,030
Points
113
Location
Calgary, Canada
Vehicle Year
'91, '80, '06
Make / Model
Ford, GMC,Dodge
Engine Size
4.0,4.0,5.7
Transmission
Manual
2WD / 4WD
4WD
It wasn't a coil connector. It was one of the bigger ones carrying 12 or more wires. It's been almost a decade so memory isn't clear. But the rubber o-ring is inside the connector to prevent water intrusion. It dries out and makes it hard the push the connectors together. I'll assume that there must have been a wire in that bundle that was part of the spark circuit.
 

sam klassen

New Member
Joined
Dec 6, 2022
Messages
22
Reaction score
3
Points
3
Location
canada
Vehicle Year
1994
Make / Model
ford ranger
Transmission
Automatic
how do you test the coil on this? and is there anyway to see if the icm is sending a ground pulse maybe a scope?
 

RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,291
Reaction score
8,296
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
Put test light in coil's 4 wire connector's 12v wire(red one) and any one of the other 3 wires(the grounds)
Crank engine over, light should flash if "ICM" is pulsing ground


Plug in 4 wire connector to coil pack, hook up spark "tester" to any spark plug wire
Key on
Unplug 4 wire connector
Should get a spark if coil is working and powered up


All ignition coils work(spark) by cutting voltage, 12v or ground, ground is cut because its simpler and came from using points in a distributor
With Key on 12v is at the coil pack and "ICM" grounds all 3 wires to "charge up" the 3 Primary Coils
If you unplug the 4 wire connector that cuts 12v and ground so coil's Secondary coil releases it's "charge", so sparks
 

sam klassen

New Member
Joined
Dec 6, 2022
Messages
22
Reaction score
3
Points
3
Location
canada
Vehicle Year
1994
Make / Model
ford ranger
Transmission
Automatic
Can I use a multimeter and use the ohm setting to see if those grnds are being grounded
 

RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,291
Reaction score
8,296
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
No, digital meters won't react quick enough, analog meter will show voltage pulse

Cranking speed is 200rpm
Each coil in the pack sparks once each rpm
So with Waste Spark there would be 200 pulses each minute, so 3 pulses each second
Digital meter would just show steady ground or steady 12v

Test light would flicker, analog meters needle would as well
 

sam klassen

New Member
Joined
Dec 6, 2022
Messages
22
Reaction score
3
Points
3
Location
canada
Vehicle Year
1994
Make / Model
ford ranger
Transmission
Automatic
So let me try to understand the icm it is grounding the coil correct? Is it when it gets grounded it sparks ok when it stops being grounded it sparks
 

RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,291
Reaction score
8,296
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
When its unGrounded it sparks

When the Primary coil, inside an ignition coil gets 12volts and a ground it creates a magnetic field around the Secondary coil
The Primary coil just has a few windings(coils of wires)
Secondary has 1,000 times more windings

So the 12v becomes 12,000v in Secondary coil(low amps but high volts, its not creating "power")

When Primary coil's power is cut, either the 12v or the ground, the Primary's magnetic field "holding" the 12,000v in the Secondary coil collapses and the 12,000v is released, the spark

General description, if you are interested in exact numbers Google it :)


In general the reverse happens on AC voltage distribution
Wires on the poles outside carry 12,000vAC, transformers on the poles change it to 120vAC to be sent into your house
Just FYI
 

sam klassen

New Member
Joined
Dec 6, 2022
Messages
22
Reaction score
3
Points
3
Location
canada
Vehicle Year
1994
Make / Model
ford ranger
Transmission
Automatic

RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,291
Reaction score
8,296
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
So just need to power up any ignition coil then unpower it and it will spark............if its working

Also the CEL, check engine light, should come on with key on, means computer has booted up
And CEL should go OFF when cranking engine over to start, means computer is getting a valid crank sensor pulse, from "ICM" in this case(1994 computer and "ICM")
 

sam klassen

New Member
Joined
Dec 6, 2022
Messages
22
Reaction score
3
Points
3
Location
canada
Vehicle Year
1994
Make / Model
ford ranger
Transmission
Automatic
The cel goes off then comes back on then if I try again without turning it off it stays on is that bad?

Would an oscilloscope be able to pick up these ground pulses.
 

sam klassen

New Member
Joined
Dec 6, 2022
Messages
22
Reaction score
3
Points
3
Location
canada
Vehicle Year
1994
Make / Model
ford ranger
Transmission
Automatic
I can check for continuity from the 3 grnds from the icm to ground?

If so I don't get any.
 

sam klassen

New Member
Joined
Dec 6, 2022
Messages
22
Reaction score
3
Points
3
Location
canada
Vehicle Year
1994
Make / Model
ford ranger
Transmission
Automatic
ok my coil is good i grounded the yellow red one ungrounded it and spark

what else do you think it is the icm? you had said that the engine cranks around 200rpm right. so i should be able to see that on the, whats it called tachometer? so i looked and it moves a tiny bit like you can barly see it move.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top