• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

any one tried oil bath hubs on their 2wd?


ForOffRoadDriving

New Member
Joined
Aug 10, 2007
Messages
2,715
Reaction score
18
Points
0
Location
HIGHLAND, MICHIGAN
Vehicle Year
1994
Make / Model
FORD
Engine Size
3.0L
Transmission
Manual
Its been almost a year since ive modded anything on my truck cause ive just been too busy driving it and living life, but after my latest tire rotation i noticed the wheel bearings had worn in some more and gotten loose. I know my oversized tires are partially to blame for this but after talking with my service partner who has been having the same problem with his ranger weve decided to try out oil bath hubs similar to those used on semi trailers. I ordered xl pro lubes 1980 kit (minus the trailer seals and xl oil) and i got a pair of dexter axle seals and a quart of 75w90 royal purlple max gear oil for the hubs. Im planning on replacing the bearings with new ones, installing the new seals, then putting on the xl hubs and filling them up with the RP and running my front wheels without the center caps for a few weeks so i can keep an eye on the oil level and color. Has anyone else tried this or see any potential pitfalls that i may be overlooking? As long as my spindles arent too worn from the previous seals i dont think i should have any sealing problems so im going to give it a try, worst case scenario is ill burn ip my spindles and have an excuse to upgrade to 95+ spindles and convert to twin piston calipers as a result.
 


ForOffRoadDriving

New Member
Joined
Aug 10, 2007
Messages
2,715
Reaction score
18
Points
0
Location
HIGHLAND, MICHIGAN
Vehicle Year
1994
Make / Model
FORD
Engine Size
3.0L
Transmission
Manual
59 views and not a single response... am i breaking new ground again?
 

projectnitemare

New Member
V8 Engine Swap
Solid Axle Swap
RBV's on Boost
Joined
Aug 13, 2007
Messages
1,193
Reaction score
8
Points
0
Age
39
Location
Osceola Mills, Pa
Vehicle Year
1988
Make / Model
Ford
Engine Size
396W
Transmission
Manual
I have seen them on a few trailers so I can't see why it wouldn't work on a truck. An oil filled nub should last longer and run cooler than a greased bearing. I would imagine cost is the only thing holding normal folks and vehicle builders from doing it from the start. Rigs run that setup with zero issue so i don't see a problem as long as your seals work out ok.

Matt
 

snoranger

Professional money waster
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
RBV's on Boost
ASE Certified Tech
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Nov 25, 2007
Messages
13,053
Reaction score
13,526
Points
113
Location
Jackson, NJ
Vehicle Year
'79,'94,'02,'23
Make / Model
All Fords
Engine Type
2.3 EcoBoost
Transmission
Automatic
2WD / 4WD
4WD
My credo
I didn't ask for your life story, just answer the question!
59 views and not a single response... am i breaking new ground again?
I'm subscribed, waiting to see how it works out. I've swapped a few trucks and trailers over from greased to oil bearings, never had any problems.
 

kryptonitecb

New Member
U.S. Military - Veteran
Joined
Dec 5, 2011
Messages
1,313
Reaction score
19
Points
0
Location
Fort Worth, TX
Vehicle Year
1994
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
Never heard of it before but sounds like a good upgrade if all works out correct.

Sent from the road while ignoring traffic
 

lil_Blue_Ford

Well-Known Member
TRS Forum Moderator
Supporting Member
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
8,208
Reaction score
5,964
Points
113
Location
Butler, PA, USSA
Vehicle Year
95
Make / Model
Ford
Engine Size
4.9L
Transmission
Manual
Sounds like new ground....

I'd like to hear how this all works out and if it's possible to do something similar on a 4x4.....
 

ForOffRoadDriving

New Member
Joined
Aug 10, 2007
Messages
2,715
Reaction score
18
Points
0
Location
HIGHLAND, MICHIGAN
Vehicle Year
1994
Make / Model
FORD
Engine Size
3.0L
Transmission
Manual
I got the oil bath hubs in the mail yesterday, $6.00 ea from easternmarine.com, i also picked up the dexter seal but quickly exchanged them for a pair of nationals after seeing that the dexters were only a single lip seal. I think ill be doing it sunday ( tomorrow) as long as chaning the inner tie rods on terras t-bird doesnt take too long. Ill take pics and post them here and in my build, stay tuned!
 

ForOffRoadDriving

New Member
Joined
Aug 10, 2007
Messages
2,715
Reaction score
18
Points
0
Location
HIGHLAND, MICHIGAN
Vehicle Year
1994
Make / Model
FORD
Engine Size
3.0L
Transmission
Manual
I'm subscribed, waiting to see how it works out. I've swapped a few trucks and trailers over from greased to oil bearings, never had any problems.
When you converted the trailers did you notice any difference in the way the seals were designed as far as having more than two lips in it?
 

brinker88

11/2013 OTOM Winner
Supporting Member
OTOTM Winner
Joined
Oct 14, 2010
Messages
3,498
Reaction score
36
Points
0
Location
Williamsport, Pa
Vehicle Year
1993
Make / Model
Ford
Engine Size
4.0L
Transmission
Automatic
Only problem I see you having is finding a oil seal to fit your rotor and a hub cap with a fill plug in it. You're also going to run into a problem with SEALING the hub cap. It's a good idea, but really not plausible.
 

shane96ranger

Well-Known Member
V8 Engine Swap
Joined
Oct 20, 2009
Messages
8,328
Reaction score
220
Points
63
Location
Utah
Vehicle Year
1997 / 1989
Make / Model
Ford F150-Stang
Engine Type
V8
Engine Size
4.6 Triton / 5.0
Only problem I see you having is finding a oil seal to fit your rotor and a hub cap with a fill plug in it. You're also going to run into a problem with SEALING the hub cap. It's a good idea, but really not plausible.
And hope you don't get a flat.

Sent while I should be doing something else
 

snoranger

Professional money waster
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
RBV's on Boost
ASE Certified Tech
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Nov 25, 2007
Messages
13,053
Reaction score
13,526
Points
113
Location
Jackson, NJ
Vehicle Year
'79,'94,'02,'23
Make / Model
All Fords
Engine Type
2.3 EcoBoost
Transmission
Automatic
2WD / 4WD
4WD
My credo
I didn't ask for your life story, just answer the question!
When you converted the trailers did you notice any difference in the way the seals were designed as far as having more than two lips in it?
(I'm talking tractor trailers, I've never really worked on small trailers, so I cant comment on them.) The oil seals usually have a flange that is installed onto the spindle, basically a wear sleeve, only thinker then most I've ever seen. They have a rubber sealing surface on both the spindle and drum sides. The drum side is usually 3-4 small ridges, I dont recall off-hand the inner surface. I usually dont even look at it, it stays on the "wear sleeve" when I install the drum/wheel assembly. (I pull the wheels and drums all assembled, it saves a LOT of time. You can do that when you have a way to lift it.)

A seal with 2 lips, generally, 1 is to seal the fluid or grease in and has a spring inside it to add tension, the other is normally facing out and is just a low tension water/dust seal.

I found a pic of the type of seal we use. (without the wear sleeve.)

 
Last edited:

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,206
Reaction score
17,520
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual

shane96ranger

Well-Known Member
V8 Engine Swap
Joined
Oct 20, 2009
Messages
8,328
Reaction score
220
Points
63
Location
Utah
Vehicle Year
1997 / 1989
Make / Model
Ford F150-Stang
Engine Type
V8
Engine Size
4.6 Triton / 5.0
Oh damn. Forgot we were talking 2WD.

Sent while I should be doing something else
 

Ozwynn

Well-Known Member
U.S. Military - Veteran
Joined
Aug 6, 2007
Messages
6,505
Reaction score
200
Points
63
Age
47
Location
Berrien Springs, MI
Vehicle Year
2022
Make / Model
RE Interceptor
Transmission
Manual
My credo
If you can't go through it or around it, then go over it.
wow, and I was going to ask if anybody has packed their oil bath bearings on their full float sterlings with extreme pressure grease.........????????
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top