• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

90 heater core leaking into cab....


Ramcharger90

Well-Known Member
Article Contributor
V8 Engine Swap
Joined
Feb 11, 2019
Messages
2,953
Reaction score
1,708
Points
113
Location
N/A na
Vehicle Year
1990
Make / Model
Ford Ranger
Engine Type
V8
Engine Size
306, Bcam,
Transmission
Manual
2WD / 4WD
2WD
90 heater core leaking, into cab and down the fire wall in the engine bay. So do I need to pull the dash or the airbox in the engine bay? I have it looped rn since the truck is suppose to go for exhaust in less than 24hrs.
 


RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,291
Reaction score
8,293
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
No, you don't need to pull the dash

Pretty easy to change the core.
Under the glove box toward center hump is the bottom of the heater core box
There are 4, I think, 8mm screws at the 4 corners, one is up higher behind glove box, if you fold glove box down all the way you can see it

Remove the screws and bottom of the box comes off
Remove heater hoses
Put a towel down in the cab
Pull core back and tilt it to get it out, some coolant can spill out when tilting it


To make heater cores last longer reverse the hoses at the firewall every few years, that reverses the flow thru the core and helps keep them cleaner
And change coolant, lol.
Heater cores get leaks when passages get blocked and coolant can no longer circulate thru that passage, so no anti-corrosion chemicals protecting that area and you get corrosion and leaks
 

Ramcharger90

Well-Known Member
Article Contributor
V8 Engine Swap
Joined
Feb 11, 2019
Messages
2,953
Reaction score
1,708
Points
113
Location
N/A na
Vehicle Year
1990
Make / Model
Ford Ranger
Engine Type
V8
Engine Size
306, Bcam,
Transmission
Manual
2WD / 4WD
2WD
No, you don't need to pull the dash

Pretty easy to change the core.
Under the glove box toward center hump is the bottom of the heater core box
There are 4, I think, 8mm screws at the 4 corners, one is up higher behind glove box, if you fold glove box down all the way you can see it

Remove the screws and bottom of the box comes off
Remove heater hoses
Put a towel down in the cab
Pull core back and tilt it to get it out, some coolant can spill out when tilting it


To make heater cores last longer reverse the hoses at the firewall every few years, that reverses the flow thru the core and helps keep them cleaner
And change coolant, lol.
Heater cores get leaks when passages get blocked and coolant can no longer circulate thru that passage, so no anti-corrosion chemicals protecting that area and you get corrosion and leaks
Sounds simple enough. Ill have too order one. Thanks
 

Bird76Mojo

Well-Known Member
V8 Engine Swap
Joined
Jun 28, 2009
Messages
2,633
Reaction score
1,264
Points
113
Location
IL
Engine Type
V8
That's one of the best things about the older Rangers. The ease of replacing the heater core. Just a handful of bolts and the job is done. Instead of spending a day or two removing an entire dash. Or like my buddies Jeep, removing the entire dash AND disconnecting the A/C system and having to pay to get that serviced afterwards..
 

Ramcharger90

Well-Known Member
Article Contributor
V8 Engine Swap
Joined
Feb 11, 2019
Messages
2,953
Reaction score
1,708
Points
113
Location
N/A na
Vehicle Year
1990
Make / Model
Ford Ranger
Engine Type
V8
Engine Size
306, Bcam,
Transmission
Manual
2WD / 4WD
2WD
That's one of the best things about the older Rangers. The ease of replacing the heater core. Just a handful of bolts and the job is done. Instead of spending a day or two removing an entire dash. Or like my buddies Jeep, removing the entire dash AND disconnecting the A/C system and having to pay to get that serviced afterwards..
I know I had the old one out in 30 mins and took 15 mins to put the new one in and funnel filled it so there was less air in it. It takes me longer to find my tools im still in the process of cleaning up the garage and my tool box has been out of room years ago.
 

Ramcharger90

Well-Known Member
Article Contributor
V8 Engine Swap
Joined
Feb 11, 2019
Messages
2,953
Reaction score
1,708
Points
113
Location
N/A na
Vehicle Year
1990
Make / Model
Ford Ranger
Engine Type
V8
Engine Size
306, Bcam,
Transmission
Manual
2WD / 4WD
2WD
No, you don't need to pull the dash

Pretty easy to change the core.
Under the glove box toward center hump is the bottom of the heater core box
There are 4, I think, 8mm screws at the 4 corners, one is up higher behind glove box, if you fold glove box down all the way you can see it

Remove the screws and bottom of the box comes off
Remove heater hoses
Put a towel down in the cab
Pull core back and tilt it to get it out, some coolant can spill out when tilting it


To make heater cores last longer reverse the hoses at the firewall every few years, that reverses the flow thru the core and helps keep them cleaner
And change coolant, lol.
Heater cores get leaks when passages get blocked and coolant can no longer circulate thru that passage, so no anti-corrosion chemicals protecting that area and you get corrosion and leaks
You should add this to the tech articles the 8mm is correct and thats basically the whole process.I would add funnel fill the core after its in the fire wall
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top