• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

'85 Ranger Restomod


Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.


Shadowrider6661

D RANGED
Supporting Member
U.S. Military - Veteran
ASE Certified Tech
Joined
Aug 23, 2017
Messages
331
Reaction score
129
Points
43
Age
63
Location
Off grid Northern Arizona.
Vehicle Year
1997
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
Stock
Transmission
Manual
2WD / 4WD
4WD
Total Lift
4"
Total Drop
N/A
Tire Size
33 x 12.50 x 15
My credo
Drive it, Break it, Fix it, REPEAT !
If you want to get a little more weld from the new welder, like penetration, pre heat the metal before you start the weld. This allows me to weld 1/2" steel with my Lincoln 140 flux core welder.
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,213
Reaction score
17,528
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
Well, it is better.

At first when I put it back on I was kinda bummed, it still seemingly flopped around. Then I played with it in the daylight and I actually only have about a quarter inch up and down of flex at the end of the swing out. It still "moves" because with a basically 8' lever from the rear Axle to the end of the gate one can do a lot of picking up/pushing down on the truck itself.

Bumper goes down maybe 3/16" and the other side goes up the same. Same for if I lift up on the swing out.

So the bumper is pretty rigid, it is the bumper brackets now. Still scheming on how to change that, I have a couple ideas.
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,213
Reaction score
17,528
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
New phase for the tire carrier:





Kinda stupid but my 1943 USMC jerry can from my grandpa will look neat on the back.



Not sure if I will "use" it, I do intend on cleaning the varnish out of the inside, lining it, cleaning the old paint and rust off the outside and repainting it. More or less restoring it.

 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,213
Reaction score
17,528
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
Plates for mounting the sliders and my rear camper tie downs came back from the local fab shop today.

20210401_161144.jpg


20210401_165859.jpg
 

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,214
Reaction score
16,351
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,213
Reaction score
17,528
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
Marked up where the braces are going to land:



My scientific method for center punching holes...





Everything kind of mocked up:



Kind of hit a snag. I forgot during my engine swap days that a Ranger frame has the straightness of a wet noodle. I have the distance set about right with the front one, as you can see with two in place the slider is kicked way out at the back compared to the rocker panel... so I need to fiddle with it more to get it square.

Also played with my welder a little bit. I think it is an arts and crafts thing from Hobby Lobby or something, cranked all the way up playing on a new 3/16" plate/scrap going slow I had 0 discoloration on the back side.

It might work for tacking this... we will see. I am going to mark it with a marker too just in case it can't survive the truck ride to a real welder.
 

BlackBII

Ranger Custom
Article Contributor
OTOTM Winner
TRS Banner 2010-2011
Truck of Month
Joined
Aug 14, 2007
Messages
7,895
Reaction score
982
Points
113
Location
UT
Vehicle Year
1989
Make / Model
Ford
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
Total Lift
5
Tire Size
33
Damn man that all looks great! I bet those laser cut plates are nice to work with; one of my biggest annoyances with fab work is cutting out the brackets and drilling 100 holes. Welds on the tubing look perfect as well.

I dig the jerry can
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,213
Reaction score
17,528
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
Damn man that all looks great! I bet those laser cut plates are nice to work with; one of my biggest annoyances with fab work is cutting out the brackets and drilling 100 holes. Welds on the tubing look perfect as well.
Yeah, measuring and drilling holes in 12 plates would have gotten old pretty quick.

I probably wouldn't have had to do backing plates but the idea hit me for the mount that is going to get blocked by the fuel tank. If I just welded the bolts to a plate I wouldn't have to drop the tank to take the slider off. Then it hit me it would help support the frame if I had plates on all of them. I am only welding the bolts for the one mount though.

Welds do look really nice on the tubes, they came that way though.
 

dvdswan

Well-Known Member
U.S. Military - Veteran
Joined
Feb 11, 2021
Messages
2,832
Reaction score
2,900
Points
113
Location
Seattle, WA
Vehicle Year
1991
Make / Model
Ranger XLT 2WD
Engine Type
3.0 V6
Transmission
Automatic
2WD / 4WD
2WD
My credo
Keep your mind like an umbrella, it only works if its open... Continually learning.

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,710
Reaction score
13,166
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
:sneaky:

Angle grinder and hand drill huh? lol
 

dvdswan

Well-Known Member
U.S. Military - Veteran
Joined
Feb 11, 2021
Messages
2,832
Reaction score
2,900
Points
113
Location
Seattle, WA
Vehicle Year
1991
Make / Model
Ranger XLT 2WD
Engine Type
3.0 V6
Transmission
Automatic
2WD / 4WD
2WD
My credo
Keep your mind like an umbrella, it only works if its open... Continually learning.
So people are just not lucky enough to have a CNC around and local shops want an arm and nut to make them. :whistle:
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,213
Reaction score
17,528
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
So people are just not lucky enough to have a CNC around and local shops want an arm and nut to make them. :whistle:
I had jokingly implied in a text to @Uncle Gump that I made them by hand. :icon_twisted:
 

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,214
Reaction score
16,351
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.

Sponsored Ad


Sponsored Ad

Staff online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top