• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

7.5 in. rear end 'clunk'


fourhigh

New Member
V8 Engine Swap
Joined
Feb 11, 2020
Messages
29
Reaction score
15
Points
3
Location
S.E. Iowa, USA
Vehicle Year
1985
Make / Model
Ford Bronco ll
Engine Type
V8
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
currently just 2" on the suspension, body lift pending
Tire Size
31's
My '85 Bronc with a 302, C4, original (well over 100,000 miles of course) 7.5 inch rear end has developed a 'clunk', mainly under acceleration.
Kind of strange, when I was driving it (made it home, driven slowly, it's been here since) it is not a constant noise,
sounds like something sliding, and then the 'clunk', maybe every 100 feet or so. I pulled the diff. cover, and drained the oil, it looked good, and nothing metallic that I could see. No teeth missing, retaining bolts are tight. U-joints seem fine, very little, if any, play in the driveshaft or axles
each side. I put the diff cover back on with 4 or 5 bolts just snugged, jacked it up and put it in drive, with my neighbor here, it did it twice, he
felt it with his hand on the cover, but it did not do it again. Guess I will double check the bottom of the inside of the diff housing tomorrow after work. The sun is starting to set too soon too early already, I ran out of daylight. Gonna be 4 wheel drive weather soon. Gotta get it figured out.
Any thoughts ? I appreciate it.
fourhigh
 


fourhigh

New Member
V8 Engine Swap
Joined
Feb 11, 2020
Messages
29
Reaction score
15
Points
3
Location
S.E. Iowa, USA
Vehicle Year
1985
Make / Model
Ford Bronco ll
Engine Type
V8
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
currently just 2" on the suspension, body lift pending
Tire Size
31's
Sorry, this probably should have been put in the 'axles' section, I apologize,
I didn't think about it until I posted it...
 

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,693
Reaction score
13,149
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
I moved your post to the axle forum.

Is this a Trac Lok diff? Maybe you have some sticky clutches.

Usually when you have a diff problem... it is pretty clear when you take the cover off. Were there any metal bits in the bottom?
 

fourhigh

New Member
V8 Engine Swap
Joined
Feb 11, 2020
Messages
29
Reaction score
15
Points
3
Location
S.E. Iowa, USA
Vehicle Year
1985
Make / Model
Ford Bronco ll
Engine Type
V8
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
currently just 2" on the suspension, body lift pending
Tire Size
31's
Thank You Gump,
I would have to do some tag research, but I think it's just a standard 7.5. Headed off to
work in a bit, working close to home, back before dark to investigate internal
housing closer. Will update later on today. I appreciate the help !
 

dvdswan

Well-Known Member
U.S. Military - Veteran
Joined
Feb 11, 2021
Messages
2,832
Reaction score
2,894
Points
113
Location
Seattle, WA
Vehicle Year
1991
Make / Model
Ranger XLT 2WD
Engine Type
3.0 V6
Transmission
Automatic
2WD / 4WD
2WD
My credo
Keep your mind like an umbrella, it only works if its open... Continually learning.
I would also check the rear suspension components for loose nuts/bolts, broken springs, loose shocks, etc.
 

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,200
Reaction score
16,339
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.
Can you make it happen by turning the drive shaft by hand with the rear on Jackstands?

Another thing to try would be to remove the drive shaft and put it in drive and see if it happens. Could be a transmission issue.
 
Last edited:

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,693
Reaction score
13,149
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
Can you make it happen by turning the drive shaft by hand with the rear on Jackson's?

Another thing to try would be to remove the drive shaft and put it in drive and see if it happens. Could be a transmission issue.
thats a BUNCH of Jackson's

$20.jpg
 

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,200
Reaction score
16,339
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.

pjtoledo

Well-Known Member
Supporting Member
U.S. Military - Veteran
Joined
Oct 5, 2007
Messages
5,337
Reaction score
2,906
Points
113
Location
Toledo Ohio
Vehicle Year
20002005199
Make / Model
Fords
Engine Size
3.0 2.3
when it's on Jackson's stands apply the parking brake, then give it a try in F/R
a quick look at the brakes wouldn't hurt.
and don't be afraid to whack parts with a rubber or wooden mallet.
 

fourhigh

New Member
V8 Engine Swap
Joined
Feb 11, 2020
Messages
29
Reaction score
15
Points
3
Location
S.E. Iowa, USA
Vehicle Year
1985
Make / Model
Ford Bronco ll
Engine Type
V8
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
currently just 2" on the suspension, body lift pending
Tire Size
31's
Thanks Guys,
I appreciate all of the suggestions. As soon as I got home from work,
I jacked it up again, placed jack stands and removed the cover. Absolutely
no signs of any metallic bad things in the bottom of the housing. All bolts tight.
No noise when I rotated driveshaft by hand, I noticed there was a little bit of
play in the gears when spinning it one direction to the other.
I then started it and put it in drive. It never did make the 'clunk' noise, forward or reverse....
Kind of wondering if it will only be doing it when it is rolling with resistance except
for last night jacked up, when it did it twice with my neighbor here. Gotta apologize,
describing the noise is tough to replicate on the web, I understand only so much help can be offered.
It's just an unusual situation that has me baffled.
B.T.W., according to the wealth of knowledge that the tech library is, my axle code 42 is an open 7.5" 3.45 ratio.
Thank You all.
fourhigh
 
Last edited:

cbxer55

Well-Known Member
Joined
Oct 9, 2009
Messages
1,863
Reaction score
763
Points
113
Location
Midwest City, Oklahoma
Vehicle Year
1998
Make / Model
Ford
Engine Size
3.0
Transmission
Automatic
I recently had my axle rebuilt by a friend's shop while they were installing 4.10s, also a 7.5 open. It was making some noise on sharp turns. Ends up the spider gears were worn some. Not horribly, but the edges were pretty well rounded. Friend said, "You can sell the 3.73 ring and pinion, but don't sell the spiders". Since the rebuild, no more noise on hard turns.
 

Sponsored Ad


Sponsored Ad

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top