• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

2.3L ('83-'97) 2.3L valve springs


Otto57

Member
Joined
May 8, 2019
Messages
86
Reaction score
7
Points
8
Location
Michigan
Vehicle Year
1988
Make / Model
Ford Ranger
Transmission
Manual
Currently rebuilding an early 2.3L and I'm upgrading to a roller camshaft. I wanted to replace the valve springs but can't seem to find anyone that has new original style. Anyone have any sources or leads to where I might find them? Thanks in advance
 


Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
I have no useful info lol but I didn't even know there was a roller cam option for the Lima. Got any other info?
 

Otto57

Member
Joined
May 8, 2019
Messages
86
Reaction score
7
Points
8
Location
Michigan
Vehicle Year
1988
Make / Model
Ford Ranger
Transmission
Manual
The 89 - 94 2.3L had a roller camshaft. Earlier 2.3 had a non roller cam with slider type rockers that just ride along the cam and the wear from the friction of the sliders is bad. The roller type cams last forever.
 

scotts90ranger

Well-Known Member
RBV's on Boost
Joined
Feb 28, 2001
Messages
7,929
Reaction score
4,227
Points
113
Location
Dayton Oregon
Vehicle Year
1990, 1997
Make / Model
Ford
Engine Type
2.3 (4 Cylinder)
Engine Size
2.3 Turbo
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6
Tire Size
35"
I had a hard time a few years ago finding valve springs when I rebuilt mine. I think I gave up and just reused the original springs These things aren't really known for valve float anyway if using a stock cam.

The Lima's were roller cam through the end of the 2.5L too, they just used smaller valve stems in the newer years, I'm running a Ranger roller cam in my turbo 2.3L since the profile is apparently close to the turbo cam and you get to upgrade to roller...
 

scotts90ranger

Well-Known Member
RBV's on Boost
Joined
Feb 28, 2001
Messages
7,929
Reaction score
4,227
Points
113
Location
Dayton Oregon
Vehicle Year
1990, 1997
Make / Model
Ford
Engine Type
2.3 (4 Cylinder)
Engine Size
2.3 Turbo
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6
Tire Size
35"
Wait, Dirtman, you had the head off a 2.5L not too long ago and you didn't notice the rollers? Or did you not get that deep in there?
 

Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
Wait, Dirtman, you had the head off a 2.5L not too long ago and you didn't notice the rollers? Or did you not get that deep in there?
Nope, did not notice. :dunno:

I honestly thought everything on the head was identical all the way back to 1974 except for the dual plugs.
 
Last edited:

scotts90ranger

Well-Known Member
RBV's on Boost
Joined
Feb 28, 2001
Messages
7,929
Reaction score
4,227
Points
113
Location
Dayton Oregon
Vehicle Year
1990, 1997
Make / Model
Ford
Engine Type
2.3 (4 Cylinder)
Engine Size
2.3 Turbo
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6
Tire Size
35"
The exhaust side has been the same since then, but there's been like 5 intake manifold patterns, like said above went roller cam in '88 or '89 then smaller valve stems in '95 or '96 which held until mid '01 when the 2.5L stopped.

They look very similar other than the big roller in the middle of the follower which makes the follower wider so the old tool doesn't fit over them...
 

Otto57

Member
Joined
May 8, 2019
Messages
86
Reaction score
7
Points
8
Location
Michigan
Vehicle Year
1988
Make / Model
Ford Ranger
Transmission
Manual
Ok guys, I'm not having any luck. Guess I'm going to the junkyard. Thanks anyway
 

tomw

Well-Known Member
U.S. Military - Veteran
Joined
Aug 15, 2007
Messages
1,613
Reaction score
46
Points
48
Location
toenails of foothills NW of Atlanta
Vehicle Year
1985
Make / Model
ford
Engine Type
2.3 (4 Cylinder)
Engine Size
lima bean
Transmission
Manual
2WD / 4WD
2WD
My credo
vertical and above ground
If you can find them, you can check the spec for spring pressure at a given height. If your springs are lower, you may be able to use shims(washer like) at the valve spring base on the head. You would add shims to get the pressure to the specification at the specified height. A spring tester uses a pressure gauge and a lever to compress the spring. It will push back with so much force when squished to the height stated. The shim is use by many builders with good success. If you are looking for performance parts, Racer Walsh and Esslinger were two names that come to mind, along with the cam manufacturers. You can read about alternative cams on this site and multiple others.
tom
 

Otto57

Member
Joined
May 8, 2019
Messages
86
Reaction score
7
Points
8
Location
Michigan
Vehicle Year
1988
Make / Model
Ford Ranger
Transmission
Manual
Ok thanks, I'm going to try the junkyard and measure the springs and see how it goes. Thanks for the info
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top