wiring

Hello gents! My sons and I are nearing completion of our LS swap Ranger. Currently I have the TCC wire that I’m needing help locating 12v to wire into. It has to have 12v constant until the brakes are applied. I wanted to wire into the brakes switch but I’m unsure because the brakes with is much...

So I went out and dug out my truck today and went to wash the windshield and my wipers stopped in the up position and wont move on there own now. My pissers still work and if my understanding is correct they are on the same circuit so no blown fuse... I think? I'm thinking a bad wiper motor but...

i have no brake lights to the tail lights or 3rd brake light 2005 b4000 4x4 so far: replaced pedal switch checked connections to multifunction switch checked grounds on bulbs i have tail lights and signals but no brake lights. i am chasing the wiring trying to figure out what wires go...

Hey fellow rangers, through a slew of craziness after my starter motor died some 6 weeks ago, I've somehow found myself in a extremely newbie mechanic situation. There is only one line ran from my fender mount relay down to my starter solenoid, which is attatched to my starter motor. One wire...

If anyone is trying to wire up some LED off road lights and have questions about the relays or what wires go where on the switches check out these videos its a simple but effective tutorial and makes the electrical work a breeze Rocker switches https://www.youtube.com/watch?v=EFsZgl4fw-U...

I have an 89 Bronco II. When I turn it over, the rear antilock light stays dimly lit (Like it's only part way engaged) There's nothing wrong with my brakes, and I used to be able to flick the ignition again really quickly and it would go out. Now it takes a couple minutes to get it off, if it...

Hey all - a friend and I are trying to get an '88 ranger 2.9l V6 up and running. Main issue is that the truck won't always start and won't always stay running. The truck starts right up when it is jumped and I've run it for up to 40 minutes (with the radio/air/lights on, putting a load on the...

Hello, I have a 96 ranger I'm putting a 4.6l dohc in. I've been researching the repining of ECU Harness. I am unfamiliar with this part. I have a 98 mark vii motor. I'm unsure on what computer to run, and I haven't really found good diagrams and or instructions on repining the harness from...

I have a 1984 carbureted 5.0 out of a lincoln town car in my 1984 ranger. I am using the stock wiring harness from a 1983 ranger but im not sure what which wires go to what so I can splice them to the wires on the motor. anyone have some kind of diagram. this is probably kind of confusing i...

Background info: 1998 Ford Ranger: 4.0; 4x4; 5-speed Currently 291k miles, The problem started at around 275k miles. I have spent countless hours on this one problem, I have taken it to three different shops and spend a fortune with no results. The problem: It seems like there is an...

Has anyone swapped an 89 B2 to 4WD from 2WD with the God awful A4LD and electric shift t-case? If so, how would you wire the electric shift into the transmission harness? Is it already on the wiring of a 2WD B2 or will I need to steal one from a donor truck?

So I've been on here quite a bit and I currently have a build thread going. I'm almost done building my motor and was looking ahead to my next task to overcome. So some basic details before going in about my build. 86' 2.9 A4LD 4x4 converting to an 5.0 & C4 retaining the original BW1350...

I'm looking for the pin outs of the 42 pin engine to body connector for a 1998 ranger 2.5 and also a 2000 expo 5.0 I've heard I'll need to swap some pins to make them work together and would like to have the info before I pull my truck in to start the swap

I've got a 302 crate motor from ford (M-6007-X302 to be exact) and I need a distributor to match. I'm going carbureted with a Holley 570 Street Avenger. I purchased a Proform 66969BK Vacuum Advance HEI Distributor with Steel Gear and Black Cap for Ford 221-302 from Amazon...

Ive got an 03 ranger single cab that came with a 3.0 stick shift. I'm using an early 97 explorer pcm so I went to the junkyard and cut the 42 pin connector off of the body side of a 5.0 explorer and I cut the 42 pin engine harness side of the ranger. I want to make a jumper harness between the 2...

I have ran into a problem that the previous owner of my truck failed to mention. He torched some wires on the harness section that goes to the fuel inectors o2 sensor and possibly the tranny. I got a harness from the junk yard for my truck off a 97 Ranger 4.0l the only difference between it and...

How are you doing, I have a quick question. My truck won't start and I diagnosed it to what I am pretty sure is the clutch pedal position switch. My plan was just splice it straight through. My question isn't which 2 splice together. My question is what are the other 2 wires (4 total) and do I...

as the title says with my new mass air it runs awful, even died a few times (new fomoco mass air number 2 incase the first one was bad) it was doing this with the old mass air as well. then i think it quit because it ran a whole lot better, now i just have it unplugged and it runs how it used to...

Bought an '88 Ranger XLT 2.9L 4X4 standard transmission recently. I have had three starters crap out and am on number four (fourth in a week). All three of the first starters lost their ability to engage the fly wheel (a lot of whirring). This most recent starter had installation instructions...

Hello my truck came with power mirrors but I disliked them so I did the 06 ranger mirror mod but I have to match wires from the 06 mirrors to my 95 mirror wiring. Can someone help me out with what color wires match up? My 95 wiring is yellow red and blue and the 06 wire colors are green purple...