transmission

I have seen a great deal of issues with the 4R44E transmission offered in a number of Rangers. I am on my second transmission in my truck and am in the process of working out a slight 2-3 flare. No solution as of yet but I am working on research. While conducting this research, I thought it...

I have an 89 B2 with a 4.0L and an A4LD. Which manual transmission would be easiest in terms of fabrication to swap in?

Getting the 2000 ranger ready for some wheeling with water. Where is the tranny vent to raise it up? 4 liter, automatic transmission

Hi Everybody! This is my first time posting, but after combing through some of the forums it seems like a great place to get some advice. I found you all through this thread: http://www.therangerstation.com/forums/showthread.php?t=131911 Basically, my clutch pops out of 5th when I apply...

Has anyone ever rebuilt a FM146 tranny? If you have I need to know everything. Any manual or repair guide for this transmission? Do I need any special tools? How long will it take? Any expertise will help greatly.

I have FM146 transmission in my 92 Ford Ranger 4wd. I just want to know what brand would be best for this transmission? Would I need any special tools? Are there any repair manuals or guides for this transmission? How long will it take?

We are changing a transmission on the Ranger. the transmission was rebuilt and when we put it in we can only get the transmission close to the engine block, it won't seat all the way (it is staying about 3 thread lengths put the guide away from the block). Does anyone know what could be stopping...

Just curious as to the best transmission I could use. I currently have the 4.0 ohv in my 97 ranger auto. I will being a swap with a sohc from an explorer (1997-2000) and was wondering what transmission I should use, considering that it is a daily driver and I WILL be adding more power down the...

I just had the tranny rebuilt and it's still not driving, we noticed that the flexplate is grinding against the oil pan, I'll upload a picture tomorrow. My question is, is a manual crankshaft (my new motor is a 3.0 from a manual, while mine was auto) different then a automatic, also is it...

Hello all, I have a few questions about my '89 ranger with a swapped '91 3L engine and tranny. I'm only 16, so I've recently started towing a trailer with a mower on it around town trying to make some money. Here recently the 1-2 shift has become bad! It wants to hesitate to shift and get real...

While i am getting ready to work on my transmission, I am gathering my data as well as reading all of the information in these news groups. I am going for the valve body gasket and probably the solenoids. (EPC) But like I said I'm still investigating. Symptom: Does not shift from 2-3 unless I...

We just finished installing a new motor in my 1998 Ford ranger, when we started it up we noticed a noise, kinda like a knocking noise, and noticed it was coming from the transmission. I have an automatic in my truck. We took off the little plate to see if it was a loose bolt on the torque...

Hey guys I have a 1999 ford ranger 4.0 4x4, am having problems with my automatic transmission. Heres the problem. After driving it for about 10-15mins the OD light comes on and flashes. Once it starts flashing, feels like the tranny is slipping and it shifts threw the gears hard. It doesnt do...

Any hints on where to start troubleshooting my TCS not turning overdrive off? I use it a lot driving in the mtns, I work at a ski area. Yesterday it just stopped working. No indicator on the dash, and it doesn't downshift either. The 95 has the little button switch on the end of the gear...

Hello, I have a 1983 Ford Ranger with a 351windsor and an AOD transmission. I recently finished up putting it all together. It ran fine and smooth, then when I went to test drive it I had no gears. Absolutely nothing, well Park and Neutral work. The transmission came with the truck and I didn't...

My truck has a manual trans an jerks hard when I shift if I don't let the clutch out REALLY slow, trans mounts? Motor mounts? Bad clutch?

so I found this other thread and they just stopped without really throwing the answer in my face....heres the link http://www.therangerstation.com/forums/showthread.php?t=79775 I am having all of the same symptoms... heres a quick rundown if u don't wanna click the link... put 3x...

Well, after breaking the first 89 A4LD, and using the successfully mounting the second A4LD that came with the vehicle when purchased, my father and I realized that the shift lever was not facing towards the ground as it should, but up towards the floorboards of the Bronco II. We disassembled...

so I have a 99 ranger xlt 2wd ext cab auto trans 3.0 engine putting a different trans in the truck. TC went in transmission first and clicked in 2 times. put trans up to engine...everything lined up... put 1 bolt on either side of trans. ( where the alignment pins are on the block) i turn...

so I have to replace the auto trans in my 99 ranger 3.0 the truck originally had the 4r44e in it I found a guy parting out a 97 ranger with a 3.0 and auto trans. how do I figure out if its got the 4r44e in it? and can someone send me a list of all the years that the 4r44e came stock? :dunno: