swap

Hi, I am swapping out a trans on my 05 fx4 ranger. The new one came with a torque converter but I left the old one in. I can't get the trans to seat properly, I can get all the bolts in but there is still about a 3/8 inch gap, the dowels are lined up but aren't going in. I was thinking the...

Swapping in a 4.0 to my 91 2.3 ranger. My question is if the dash harness connector (big white connector) is the same on all engines for my year or if the 2.9 and 4.0 differ from my 2.3 on the dash side. I can find that the 2.9 and 4.0 interchange but not solid info on the 2.3. I assume it does...

Hey there so my front drivers side hub has been damaged on my '95 stx 5spd (manual locking hub), and Ive been searching for a while to find a replacement in my area with no luck. I was just wondering since I know its a rare part if theres anyway to get this fixed as I hate walking out the door...

Hey, so I think I know my answer to this, but I got a Ford 8.8" axle out of a 01 ranger 4x4. I wanted to swap it into a 1997 ford ranger 2wd. Is there any kind of modifications I need to do to the 8.8 or should it just bolt straight in? I'm pretty sure it should bolt in but I understand the 4x4...

I have read tons of info on doing the 302 swap, I would love to swap one in my truck, however I am still wanting to keep the 4x4 for the winter out here in Iowa. can I use my current transfer case and rear end and front axles? or would I need to find a full size f150 with transmission transfer...

I've been using this site to look up information on all kinds of crazy idea's ive had but never followed through on any of them yet. The best thing ive completed is my sound system. My newest idea is one i really want to follow through on because it will help no matter which direction i go with...

I haven't yet done it, and I haven't seen where anyone else has done this to a later model Ranger, but I am very tempted to try it out. Not too concerned about MPG's, just looking to fit a V8 into it and lift it for a little 4x4 fun. Any and all help and suggestions are welcome, even if it is...

Hey all. I scored an '83 2.3Lima 4WD a week or so ago. Was told it had a bad HG, but there was ZERO oil/coolant contamination. Oil was just dirty, no shavings from what I could see. I got the thing running, and it would run at higher rpms (2-4k), but at low rpms it would shudder and buck like...

I have a 2001 Ford Ranger. Its a 2.3 DOHC, its now blown and does not work. I want to replace it with a v6 4.0, I need it to do it the CHEAPEST AND EASIEST WAY POSSIBLE. I need to know how many things will need to be replaced and swapped, what will I have to buy in order to complete the swap...

Want to install 4.0 and trans from 01 Ranger into 96 Ranger with 3.0 I have both trucks want to know what I will need from 01besides motor fuel lines and pump and under hood harness and computer. Do I need interior harness or instrument cluster or what else?? Any help would be appreciated Thanks..

Hi, I've posted a a couple times through this build to get some help getting it running. I have an 03 Edge with 97 5.0 from mountaineer. I have the auto in and it runs fine but I've always wanted a 302 ranger but always planned on a T5. Since my truck was already auto I went the easy route but I...

So its my second head gasket blowed since 1 year :@ so i want to go to 4.0l so what exactly i need to get before doing the swap (radiator,fuel pump, tranny, exhaust line,engine mount,...) and do i need to f*ck up with all those wire or its plug n play swap....my truck is a ranger 1991 2.9l and...

Hi, I have an 03 ranger edge ext cab 2wd that came auto with the 3.0. Don't feel like explaining what happened but the 3.0 is in the yard and the 5.0 is about to go in. I have an entire 1997 mercury mountaineer as a donor. My only problem is I'm not too great on wiring just kinda getting by when...

Just today I became the owner of a 1988 Ford Ranger. Its sitting on a full bagged system. The bags are about all that seem to be wired correctly. When I pull the lights, all but the headlight/high beams come on. It misses, has wetness everwheres. Has a ripped up bed cover and missing door...

Alright, so I have an '89 Bronco II 2.9l with 235/75r15 tires, which really bog it down, and I'd like some more power. My friend recently rolled his 2000 explorer and is willing to sell it for me $300. The roof is trashed, but everything under is fine. I've heard of people putting 4.0s in BII's...

Hey guys, I'm doing some research on converting a 2002 Mazda B3000 Dual Sport from 4x2 to 4x4. I know everybody says that this is too hard to justify, and that it's better to just sell and save up for a 4x4, but hear me out :) First of all, I've heard that changing a rear-wheel drive to 4wd...

I apologize if i'm posting this in the wrong place! ive never been apart of a forum! Im just needing to know how and what i need to swap an engine. The truck is a 86 mazda b2000 (2.0) 5 speed is there any ford motors that will bolt up easily without alot of work to it? i really dont want to...

i have the good ol' push button for 4x4, but i cant remember entirely if its powered by the ECU or the button itself (gets power from the ecu but it operates itself) believe it does. think i found the someone talking about it on here a while ago but i cant seem to find the thread again. im...

Hey guys i am currently building a 302 and i have a 05 ranger with a 3.0l manual RWD.I REALLY want to put my 302 in the truck but i heard the electronics are gonna be a pain. I was thinking would i be able to do the wiring from a 96-00 explorer into the truck and use the 302? I think that could...

I'm new here first time posting I'm swapping a 4.0 from a 97 Ranger 2 wheel drive automatic into a 1990 2.9 2 wheel drive 5 speed.the 4.0 is complete with all harnesses dash and engine along with ecm.my question is if anyone done the swap with similar years and what I need to do for the...