shifter

Help! I recently pulled my shifter to install new pins and gaskets as there was a lot of play. Upon installation it feels like it will only go into second gear and the truck is stuck in reverse. Any ideas on how I can fix this? 2000’s 2.3l M5OD transmission

I have a 2004 4x4 Ranger with the 4.0l SOHC and I believe the M50D-R1HD manual transmission (and an electronic t-case). I pulled the transmission to replace the clutch and these two pieces of rubber fell out. I know the one on the left goes on the shifter because I saw it before I took out the...

Hey guys I. Having issues with my shifter. Th where it is so worn down that it is b o uncong around in my shifter. It locked up and I called a transmission guy who said my linkage was broken I opened it up and I saw what he is talking about. The ball is just bouncing around in the sleeve it...

My shifter in my truck that you use to shift with fell out of the thing that holds it in and I think the transmission is a Toyo Koygo 5 speed but I don't really know that much about it and my truck is a 5 speed 2wd 1987 2.9l Ford Ranger, so if anyone knows where to get the part or how to fix the...

Hello all! I bought an 1984 ranger back in August and have been having problems with the shifter since. My brother repaced it in September and by March it was so loose i have to repace it again. Does anyone know where to buy or get a hold of a 4 speed manual shifter? The truck is sound besides...

Just a few questions as my swap draws to a close. 1) I have a 1973 C4 from an F100. What size are the transmission cooling fittings? I'd like to run 90 degree fittings and run line along the bottom of the passenger side head, under the harmonic balancer to the two Tranny cooling ports on the...

My shifter has been really lose for a while now and now that I got my truck driving again, I ordered the parts to replace the bushings but I can't for the life of me figure out how to remove these stupid allignmen t pins so I can install the bushings and washers correctly. Please and thank you...

My son's B2 was stuck in gear and then slipping in and out and then not going into any gear at all. We have taken the shifter out and found a plastic "thimble looking" part that the round ball end of the shifter goes into. The piece is broken all around the top and sides. Was told by a mechanic...

Hey guys, I'm trying to fix my 85 manual tranny. There is supposed to be a polyurethaine ball on the end of the stick but it came off in the slot its supposed to and is completely useless now. If I try to shift over into reverse the lever will pop out and leave my truck engauged. I need...

I want to get a new shifter knob for my 98 ranger manual and was wondering what you guys have. I might get a .44 grip. What do you think?

The column shifter on my son's 1994 Ford Ranger 4x4 with the 4.0L engine is stuck in Park. Looking for help in diagnosing and fixing this problem. So far we have replaced the key lock cylinder (old one was sloppy), replaced the stop light switch, dropped the steering column to see if there was...

I have a C4 from a 74 Montego and a B&M hammer shifter. I got the C4 cable kit and am in the process of adjusting the linkage. Rookie status... Any advice? I'm not even sure where is park on the transmission? Thanks in advance. A-

today i bought a steeda short throw shift but the part#070-997-0158 says its for a tremec but i have a 1990 t-5 out of a 302 mustang....idk much about how the shifters are different because it almost feels like it will work but its weird and this is the only shifter i have......is there any way...

First of all I have a 02 ranger 4x4 with a 4.0 motor and a manual transmission. I am trying to remove the transmission on my ranger, I have all the bolts and everything out, I have pulled my shifter off and followed every step in the Chilton manual pulling drive lines transfer case ect. It...

So far ive gotten my transfer case out right behind where that is bolted there is a box bolted on the end of the transmission where the shifter goes. where these two bolt together are leaking bad enough to cause me to loose a couple quarts of fluid every week. I got the shifter out as well and...

I was removing the shifter in my new to me 1994 Ford Manual 4x4 when I heard the Reverse Lockout release it's tension. I think I have a pretty good handle on how this whole area works. But, there's a spring that maintains the tension for the Reverse Lockout and I think this guy has slipped...