sensor

A neat little tutorial on how to jury rig a camshaft sensor sync tool for the Mazda Ranger trucks, if the parts store is closed or your finances are stretched do to the pandemic its fast cheap and dirty but works

Hey all, 08 Ranger XLT 4x4 5 Speed, ABS kicks on at low speed. Ive narrowed it down to faulty speed sensor(s), as described exactly in this video https://www.youtube.com/watch?v=7ve-eoHph2M My question for you: is there a way short of going to a dealer or finding somebody with an expensive...

So I'm sure I'm overthinking this but I just replaced my catalytic converters on my 2006 Ranger FX4 Level 2 with the 4.0 motor and I bought new O2 sensors for it. I wanted motorcraft sensors and none of the auto parts stores had motorcraft so bought them from rockauto. Banks 1 and 2 sensor 1 are...

My bronco II break light sensor will move and adjust but it will not stay in the correct position meaning it will work once but if I go to break a second time the position moves and wont stay where I put it. Does any one else have this problem and how would I fix that? Sorry if this is an easy...

So I'm going to replace my crank sensor on my 1994 california spec ranger 2.3l. it seems that this can be difficult. can anyone give me a walkthrough on this?

is it really necessary to replace the camshaft sensor synchronizer shaft along with the sensor? seems like a lot of work....

I have looked all over online and all over this sight. I have a 91 Ranger 2wd with a 8 plug 2.3 engine. Some people say that this sensor exists on the passenger firewall and have picks... I have looked over and over this whole truck and it is NOT there but people swear it should have one even...

So i picked up a triple set of mechanical gauges for my 91 ranger 2wd, 8 plug, 2.3. I have water, oil, and volts but i am stumped on where to plum and wire them in. The temp sensor i was just going to T off of the ECT location but if that messed with the computer i will just T it off a heater...

Hello everyone first time poster here. I am posting on the behalf of my uncle who has no knowledge of computers whatsoever, and needs help regarding the camshaft position sensor. He's got a 4WD 98' Ranger, 4.0L manual. Any help at all would be much appreciated! The following is all of the...

Coolant Temperature Gauge I have a dead temp gauge. I have great heat, enough that I'm sweating in the cab. As I've had some vehicles die on me from overheating I'm over cautious and am running the heat at full blast when I drive. I haven't driven it further than 20 miles yet so its not too...

this is a little long winded but PLEASE bear with me i really need your guys' help... :sad: About a month ago my b3000 quit running on three cylinders. I put a new coil new plugs and wires on it and nothing changed. Took it to a local shop that we have taken our vehicles to for YEARS and they...

wednesday night I was out and hit a rock I didn't see in time with my lower control arm. I'm replacing the arm tomorrow but the shock from the hit set off my airbags and I don't want to go to the dealer to have them drain my bank account so I have a few questions. What do I need? I know I'll...

Last weekend I went out wheeling and hit a few puddle going as fast as I could and the force ripped my VSS off the diff and when I went to plug it back in (this has happened before) the plug in the axle had been ripped out so I went the last week without a working speedo. I put in the new VSS...

So after days of searching and calling around i am at a dead end. I drive a 93 ranger 2wd auto trans. I need a cam sensor. Everywhere i look online i can only find 94 and up. All the parts places i call tell me that my truck doesn't have a cam sensor. What gives?

I'm guessing the airbag from a 98 should be identical to the one in a 99, right? How would I go about removing one from a parts truck I found without setting it off, then installing it in my truck? I know I have to disconnect the battery and get the computer reset. Do I reset the computer...