help needed

Ok so my 97 2.3l 5spd sat for about 4 or 5 months after I got it back it will start and almost immediately stall out unless I stay on the gas I changed the air intake control valve that didn't help so I took it today and got it put on the tester and got a code for mass air flow sensor an oxygen...

Hey, I am currently in the middle of swapping a 3.0 v6 for my previous 3.0 v6. The motors are now exactly the same because I swapped some parts and no I am putting it back in. I have the engine on the engine mounts on the truck and the transmission almost hooked up but it has about an inch to go...

Ok, so I am currently having a couple of issues. 1. My 2001 4.0L shakes when its at idle. It's not a massive or alarming shake but it's definitely not supposed to do that. 2. I am trying to figure out where the EVAP solenoid is located. Need some help. Just started doing my own work on the...

I've got a stock 2009 2wd xlt ranger and am in need of help sizing my tires. I've heard that you can put 31s on it with no lift and rubbing, so that's the size I'm going for. the tires that are currently are on there are L215/75R15. I don't know how to size a tire to fit it on my rim, and...

I love this forum and all the input ive gotten on previous threads. I bought my Bronco about 6 months ago and have been working on getting it to perform in the mountain of colorado (6600-10000ft elevation) depending on where im driving. Heres what Ive done. Any thing else anybody knows that...

Hello, This is my first post and am really looking to get some help I apologize if this isn't the right place. I have been having an issue getting my 88 Bronco ii 5 Speed Manual to idle where it is supposed to. What happens is that when the engine is cold started the engine RPM will sit at...

Very new to this but my grandpa had an 85 ranger just sitting and told me if I could get it running I could have it. Needless to say it is a fully functional vehicle now. But it is creeping up on 150k miles, so I find myself planning for the future. Moving on, I had a quick question I was...

Doing a 5.0 explorer swap into my 95 ranger. first thing to know is i have a custom 8in short arm suspension lift in my truck. i am doing a 97 explorer 5.0 plus trans. truck is regular cab short box 8.8 axles twin ibeam Was looking at using the explorer transfer-case or my current ranger one...

i have a 1994 ranger 3.0 2wd with an automatic transmision. the truck was bought used and is claimed to have a new engine. The engine runs great but the transmision hasnt been taken care of and hasnt had new oil. Normally i would want to change the oil but im afraid if i do the transmision will...

I've been stuck on this for a while. I have replaced the fuel pumps, new filter new gas tank. the truck primes up and starts but wont stay running it slowly just dies down from fuel lost I'm guessing. It will start again but the system has to be re-primed. the fuel pressure regulator has been...

I have a 2000 ranger and I am wanting to do some upgrades. My ultimate goal is to have solid front and rear axles, lifted and 35s. My main uses of the truck would be to go through major mud and snow and pulling out other trucks and small tractors since I live on a farm. Just need some advice on...

Hey everyone I just bought a 98 ranger 4.0L manual a few weeks ago! So I am pretty new to this forum thing and my knowledge of cars and trucks isn't the greatest but the Ranger had been sitting for several years and the owner would drive it maybe two or three times a year just to move stuff. So...

Hi, I'm looking for tires for my 96 ranger. I'm 17, just bought my first truck. I grew up in a town where your truck showed who you were. I know what tires I want on my ranger, but they're ungodly expensive. I'm trying to find 265/75r15. 245s would be better for me but I cant seem to find them...

I replaced the head gaskets on a 91' Ranger 2.9 liter v6. I made sure to mark the distributor so it went back in the same way it came out. After I get it all back together, it wont start. I made sure all pigtails are connected etc. I found that I am getting power to the coil but no spark from...

I have a 1993 ford ranger with a 4.0 and auto trans I just swapped the trans cuz I lost first gear. After the swap the truck holds idle and can redline but once I put a load on it (drive ect) after 1500 rpm the truck starts to die to keep it going I pump the gas but after it catches up stalls...

Help needed please, I replaced U-Joints, Carrier Bearing, marked the driveshaft so I put it back together correctly and now I have a terrible vibration. At low speeds (15-35 mph) it feels like the rear end is hopping. At 45+ mph the entire truck goes into what feels like space shuttle re-entry...

:dunno:Please. I am at my wits end with this truck. 1995 Mazda b-3000 4x4 manual 5 speed tranny, 3.0 engine. History= Last year I replaced the slave cylinder and master cylinder, and has been fine for at least 14 months. Yesterday as I was driving past a school in residential area( so I was...

I have a 99 ranger 3.0l v6 I hydro locked the shit out of it saturday night, blew the hell out of the valve, so i bought a new cyl head from the dealer, tore engine apart, slapped new head on there (along with brand new gaskets for everything) then reassembled my whole engine and its still...

OK, Have a 83 ranger with 2.8, just did duraspark conversion and installed holley 2 barrel. Can't get the truck to fire up. thought it was a flooding issue, but cleared all cylinders with blow gun and still won't fire. Cranks over just fine, was getting a spark when took plug out. Any...

I am looking for someone to point me in the right direction. I need to get 2 modules for a 1998 4X4 4.0 Liter 5speed Manual A/C Supercab: 1 GEM (Generic Electronic Module) 1 RAP (Remote Anti-Theft Personality Module) I am looking for my uncle, who is computer illiterate....but I am...