explorer

I had a custom bent tail pipe made for my 84 Ranger and would like to put it on my 97 Explorer. Has anybody ever interchanged pipes on these 2 trucks? Thanks in advance!:beer:

I have a 96 explorer sport with a blown 5 speed standard trans And I have a 98 Expplorer xlt with an auto Wandering if any one know how to swap the electrical parts to my sport I already know how to swap the tranny itself

Hi guys, I have a stock 5spd 87 bronco II. I'm looking to lift the truck so I want stronger axles, I found a 92 parts explorer for a couple hundred bucks. its got about 200k on it with a rebuilt 4.0 auto trans. Now my questions are will I be able to use both front and rear axles from the...

As always, you guys help me out when my truck decides to have it's moments... Figured I'd ask here first... 94 Explorer XLT 4x4 BW1354E Auto Hubs M5OD 4.0 When driving it sounds like something is making a notable humming noise in my front end. It made this sound once before when I turned the...

Sooooo do i remove the 95 4.0 egr stuff n cap ends/ block ports?? personally id rather not have the egr(less stuff to go out/fail) or leave it all attached but not hooked up???( engine my run like crap) cuz i dont want that. i wouldnt mind keeping the EGR if i could get it working properly...

Rescued Ranger / Yet Another 4.0 Swap (YA4.0S) Little back story: 1989 2.9L 5sp XLT 4x4 - given up for dead, PO had pulled intake, said it was getting gas in the oil and filling up the pan, left it sitting open topped and no rear window. I picked it up for $400 which may have been a bit much...

Im having to change the clutch in our 94 Explorer and I just have a couple questions: Does anyone know how to get the y-pipe unbolted? And how do I disconnect the "tranny line"(?) The gold fitting that goes into the tranny near the top on the drivers side. Also, we live in a smaller town...

ok, so a little bit of background, 98 ranger 3.0 5 speed, 3:73 gears 7.5 inch open differential. i want to get a ranger 8.8 L/S that i can just bolt in and go. im really not that worried about disc brakes, im fine with a good set of drums, and im not a very good welder, so the explorer axle...

I was reading about the 8.8 explorer swap, and i have a couple of unanswered questions. im not really concerned about the 28/31 spline difference, i just want the ease of a dirrect bolt in, as i dont trust myself welding on an axle. do the 8.8 ranger axles have disc brakes? how common were the...

I'm pretty sure i allready know the answer, but would 97 explorer doors work on a 98 ranger?

Hope I'm not rehashing an old topic, but couldn't find info for my application. The family vehicle is a 99 Mountaineer that needs tires this weekend or maybe next. I'd like too step up to a set of 30x9.5's or, better yet, 31x10.5's. Does anyone know if these will fit with a stock suspennsion...

I have a 85 bronco with 35's and other cool parts on it that I got at a action for a deal but it is hurting bad. I also have a 88 bronco in better but stock shape. My plan is to fix up the 88 with the 85's parts. I also just bought a 94 explorer for the 4L and axles. Now I find myself asking...

Hey everyone, I've got an 86 Bronco II with a 4.0l out of a 92 explorer, manual trans. The starter motor has been acting up the last little while, and I just want to get a new one installed so I don't have to worry about it anymore. I know a fair bit about cars, but I'm no Mechanic. Just...

Hey everyone, I've got an 86 Bronco II with a 4.0l out of a 92 explorer, manual trans. The starter motor has been acting up the last little while, and I just want to get a new one installed so I don't have to worry about it anymore. I know a fair bit about cars, but I'm no Mechanic. Just...

Well a couple months back i posted about a shuddering problem my truck was having. A lot of people jumped and said it was clutch, but it ended up the clutch is just dandy :D Since then the truck has gotten new plugs, wires, coil pack, intake boot, thermostat, fuel filter, and had the intake and...

Problem: Warped/bent/deformed backing plate on 94 explorer axle. Preferred solution: Replacement backing plates shipped to my house. The issue i am having is trying to figure out what fits. Every search i make winds up with 9" stuff. I don't want to switch to disc as i would have to buy a kit...

hopefully some of you can tell me what went wrong...i have a 2000 4wd that the springs were flat...so after reading a bunch i thought explorer leafs would be the best option...i went to my local u-pick and found a set off a 98 4 door with 80000 miles looked like they were in great...

hey i recently got an 92 explorer rear to install in my 89 ranger and it was missing the parking brake lever on one side is there any place i should look to find one? thanks

Hi, I've got an 89 BII 4x4, and I'm looking to do a cheap lift on it. I've got some F150 coils and from searching on here and reading the tech post if I understood it, I am only going to need F150 shocks, and adjustable camber bushings to do the lift. Is there a specific year/size I should be...

I have a 94 Expo XLT witht he M5OD, and it seems over the last two days it has a bit of a random shudder/skip. It happens occasionally in 3rd, But more often in low RPM 2nd. It seems to do it mostly as I step on the gas. I got it to do it a few times today if I stepped harder on the gas pedal...