• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

dana 35

  1. Manual hubs vs. live axle - worth it?

    Hi everybody, I'm halfway through converting my 2002 B3000 Dual Sport (Edge) to 4x4, and it's time to decide on a hub setup. I was originally planning on using the '98-2000 CV axles and buying the Rugged Ridge manual hubs for them, but am also drawn to the simplicity and (relative) strength of...
  2. Dana 35 SLA center pin removal?

    Hi everybody, I'm working on replacing the bearings and seals in a Dana 35 SLA axle housing, but I can't figure out how to get the center pin past the ring gear! This differential has a 4.10 ratio and the ring gear is huge. Like, the pin is barely visible behind it so grinding the teeth down...
  3. 94 Ranger Dana 35 axle shaft

    I'm looking for parts to rebuild my 4x4 axle shaft. I recently bought a 94 Ranger, 4.0L V6 - I have a few questions: anyone know where I can find parts for a Dana 35 front passenger axle shaft anyone know what years of other Fords (Explorers/Broncos) use a Dana 35 I'm in Canada; I'm 17, I'll...
  4. Unkown Clicking Sound?!

    1989 Bronco II with 1992 Explorer 4.0, Dana 35, (godawful) A4LD, Auto Hubs, and BW1350 Electrical T-Case. After replacing the front brakes, the vehicle began clicking, and was especially noticeable when coasting. The sound is difficult to pinpoint from the cabin, as we (my dad and I) can't...
  5. 2WD to Dana 35 swap help

    89 B2 w/ 4.0 and D35 from a 1992 Explorer. Will I need to get a different wiring harness? We followed the write up on the tech articles for a D28-D35. Only difference was it was a 2WD truck.
  6. The_Epsicle

    Dana 35 Grinding on passenger wheel

    I drive a 1994 Ford Ranger Extended Cab, 4.0 OHV, auto tranny, auto 4x4, Dana35 front, Ranger 8.8/3.73 rear. The odometer reads about 202,000 but it has been running fast since 15,000 in 1996, I've owned this truck since November. I have recently replaced the Ball joints and repacked the wheel...
  7. New front axle: Same brakes?

    Hi everyone! I'm working on collecting parts and information to do a 4x4 conversion on my 2002 Mazda B3000 DS (2wd). I have torsion bar suspension already, so I'm planning on salvaging a Dana 35 SLA to use as the front axle (hopefully a 98-00 so I can run manual hubs), but I'm not clear on how...
  8. Dana 35 Twin I Beam upgrade?

    Howdy all, I'm about to start tearing into my front end and fix some long over looked issues. The biggest thing I'm running into is, the slip yoke on the passenger side axle. Is there a place/site that sells them new? Maybe a stronger one? The previous own I think didn't own a grease gun so its...
  9. rangerscout

    1985 bronco ii swap need advise!

    Hey guys so I pulled the trigger on starting all the swapping on my truck today and went and bought me an 91 xploder. My question for all you guys is do i need a fuel injected bronco iis tank to make this work or can I just get the pump out of one and such I could really use the help. I live in...
  10. C130MARINE

    position dana 35.....

    Gents, im in a bit of a jam. I really could use some guidance. Okay I have a 91 Ranger ext cab STX I put a lot of lift on the truck. I ground down all the factory rivits and installed all the new brackets. Then reassembled everything. Now, I also extended the radius arms. not being a real "4...
  11. Dana 35 needed

    hey guys I'm looking for a Dana 35 ttb I'm located in western mass and been looking for a few months but cant find one to save my life other then the junk yard witch wants 300 for one and i don't know if its any good dont want to spend 300 on something i have to spend another 300 on to rebuild...
  12. Ebay Dana 35 questions

    Hello I purchased a used Dana 35 with 4.10 gears from ebay. The seller's description was: "You are viewing a third member for a 1991-1994 Ford Ranger or Explorer. This is a reverse rotation member(like factory) with 4.10 gears, professionally installed. It is set up for 27 spline axle shafts...
  13. groovygriffy

    slinger shim-inner bearing/pinion

    ok i just bought my ranger with a blown up dana 35 in the front(full of mud and no bearings left). I've bought the 4.56 r/p front/rear with master install kits. what i need to know are the dimensions for the slinger shim-inner bearing on my 1996 ranger ... i'm a machinist and plan to build one...
  14. Dana 35 manual hubs

    Did the Dana 35 on rangers or explorers ever come stock with manual hub lockouts? I've got a D28 with manual hub lockouts and want to upgrade to a D35. The only D35's I've seen are auto hubs (which isn't what I want). Thanks. -akx
  15. Is a Dana 35 a direct bolt in for the Dana 28??

    I'm putting a 351W in my 85 BII and need to beef up the front diff. I've read about the Dana 35 swap, but no one has enough detail about wether i can just bolt it in and get a shorter driveshaft or if i need to replace the whole front Twin Beam. I'd like to be able to just unbolt the 28 and junk...

Sponsored Ad


Sponsored Ad

Top