• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

cluster


  1. 1992redranger

    Dashboard Instrument Cluster Swap

    Hello all! The speedometer, odometer, and gas gauge stopped working in my 1992 Ranger, 2.3 4CYL, manual transmission. Lucky me, though, because I found a replacement cluster off a 1990 Ranger, 2.3 4CYL (Ebay listing here). I'm hoping to swap out the cluster myself, but have never done this...
  2. 2.3L ('83-'97) Tach cluster swap

    my truck is a 94 2wd/5spd 2.3 standard cab. Just need to know what wires need to (or even can) be moved around in the plugs to be able to use an instrument cluster with a tach from a 1989 bronco ii (2wd MT with 2.9) It is not plug and play, despite appearing to be. I did keep the connectors...
  3. Tach not accurate

    1991 3.0 XLT 5-speed; 268,000 miles. Bought the truck new; sold it to a friend and got it back recently. Now, the original tachometer is registering about 50% too high. When the engine is idling around 800 rpm, the tach is reading about 1300. Normal cruise at 2000 rpm is registering 3000...
  4. Cluster swap questions

    I was looking for a Sport Trac cluster in a parts yard and while I didn't find one in a Trac, I found a 2001 Explorer (even had a 5 speed, nice!) with the same white face gauges so I picked it up. I was just wondering if this would be plug and play into a 2000 Ford Ranger 2.5L. I've searched...
  5. All about them gauges

    So I have a 93 Ranger 4.0L 4x4 with a manual transmission. Problem: All of the gauges with the exception of the speedometer gauge are dead. The speedometer gauge goes crazy when you accelerate and goes to the correct speed when you let off of the gas. When it happened: I knew a guy that...
  6. ABS light/seedo bounce 1999 ranger

    Hi guys, got a fresh new problem to deal with. I have a 1999 ford ranger xl, single cab rear wheel drive. yesterday my abs light came on and my speedometer started to bounce. It engages around 60 km/h when accelerating, and when braking it will bounce down to zero once I go below approximately...
  7. Tips on installing white face gauges

    I just finished installing white face gauge overlays in my 2004 Ranger and I have a few tips to add to the already terrific, detailed instructions on this forum on removing and re-installing the cluster. If you have an automatic transmission, you'll need to disconnect the shift-indicator cable...
  8. 1986 Bronco II Instrument Panel Dummy lights

    Just picked up a Bronco II (2.9 5 speed, 2wd) which I had to do a lot of reassembly. Unfortunately, the overlay for the dummy lights is missing. Could someone please identify these for me so I don't ignore the oil pressure light thinking its the seatbelt light! There are 8 divided sections on...
  9. Install Cluster W/Tach!

    Hello, everyone! I am new to the site and was wondering about changing out my cluster for one that has a tach, there seems to be some really sharp people on here and I would say someone has done this very thing before and would know what needs to be done to do this. My truck is a 1996 Ranger...
  10. 01 Sport Trac Instrument Cluster in 95 Ranger - Wiring Diagram for either?

    I swapped out my bad cluster without tach with a good condition Sport Trac cluster with tach. Everything works without issue except for the tach. It will show proper idle rpms, but will not go above 2000 or so. I spoke with a mechanic and he stated that the tach needed a ground cable...


Top