carburetor

Hello all, I recently rebuilt my dad's 1984 V6 2.8L Cologne Engine. It is the carbureted variant. The original engine got to 210,000 miles before we decided it was time to rebuild when it was leaking oil like crazy. In the process of rebuilding the engine, I replaced the carburetor with a...

I got a 5.0 in my ranger out of a 1984 lincoln town car (not 100% sure on the year but everything seams to work with the 84) with the motorcraft 2100 carburetor on it, does anyone have a diagram on where all the vacuum lines go.

Hey, I've been lurking around looking for info on carbs that will work when I switch over to Duraspark. The tutorial says a motorcraft 2150. I see a ton of carburetors some off old mustang 2s and bronco 302s. Will I be ok as long as I get any non feedback 1.08 venturi carburetor with electric...

Alright guys new to this sight I'm sure I'll get some Awsome information though. My plan for my 2005 4.0l ranger edge 4X4 is to basically change everything about it internally. Haha. I wanna swap in a v-8 make it carbureted and keep it 4x4. Is this possible or am I crazy?:dunno: Also I'm...

I know "loss of power" has been answered before, (and believe my I've searched) but I feel my situation is unique. As soon as my 302 swapped Ranger was driveable, it ran great. The slightest tap of the gas pedal would roast the tires (or tire, with the stock 93 open differential haha). About a...

Alright il give you guys some backround. I bought the truck a couple weeks ago n it had a high idle n sticky throttle problem so chasing that ive replaced the idle speed control motor, throttle position sensor, and rebuilt the carb last weekend. the throttle doesnt stick anymore but it just...

Hi, Have a 1983 ranger rwd with a 2.8 v6. Just rebuilt the carb and it's leaking fuel from behind the pump relief valve assy. The fuel seems to be coming from a tube that runs behind the pump relief valve assy. and the tube runs into the accelerator pump. Any ideas how to fix this, this is my...

Hello, I am asking this question because i have found cheap b2 being parted. I own an 86, iam wondering if the dash and windshield will fit. Aswell as the throttle and choke levers will be compatible with the current carburetor. Iam new to b2 2.8 so please give some advice.

To whoever may be able to help: I just bought a truck last week that had some carburetor issues. I’ll give the specs, then state my problem. 1984 Ford Ranger 4x4, 4-speed manual 2.8 liter V6 Carb ID = E37E AEA, 1.08 So here’s the situation. The carburetor was pretty messed up. So I pulled...

Hey, I got a 1988 2.0l carb engine what can i put in it to increase HP, torque and just over all power? I know I can buy a new carb, exhaust, and a K&N air filter but what else can I do and what kind of carb works the best?

I posted this once before but have some better information now. My bronco seems to run fine for about 30 seconds up to 2 minutes and then the idle gets super rough. About 15 seconds after that it stalls out and won't start for about 20 minutes. What could all of a sudden make a good running 2.8...

Went to start up by 84 B2 this morning and it ran fine for about 30 seconds. At that point it started to idle rough and about a minute later stalled. It will run normally if you hold your foot down on the gas pedal just a little bit. I took of my air cleaner and noted there was some fuel spray...

This ancient truck has a 1 barrel carburetor, 5 speed manual transmission, 2 wheel drive. I took the carb off and took it to a shop and they rebuilt it for $145. Put it back on and I can barely make it uphill in 3rd gear. Before the rebuild it would just fly up that hill. It also backfires...