My duraspark/offyhauser 2.8 is leading me to be leave it is running lean. My father an d I want to check timing and set the carb flow but cannot locate 2.8 pinto settings. Any one got links or info for me to tune this thing please
Sent from my SM-G530T1 using Tapatalk
My pop installed headers on my B2 before he gave it to me. the head gasket went bad and now i am trying to replace it but i need new exhaust gasket for the headers if any one know where i can get a set that would be great
for the 2.8 but the headers are unknown....i did have to weld a erg...
its getting cold out and i have a offey intake with 4bbl carb. on a 84 with 2.8. my b2 is cranky when its cold. i figure the air temp is causing slight carborator icing. so i am looking for a heat riser on a aircleaner. i cant seem to have luck with after market.
i was wondering if...
i know of lmc and broncograveyard.com
I need both RH and Front Lower 1/4 Patch Panels
i can get them from broncograveyard for 105. shipped for the pair. any better sites?
my wife said her car was starting to move like a dog the last week but once it built up speed it was fine. so i am like wtf what in the hell are you talking about. I test drive it and discover it starts out in 2nd gear. so i drive it probably 1/8th of a mile and back home and find that...
was looking for a new hat handle for my b2 on fleabay and found a guy selling wings?
http://www.ebay.com/itm/FORD-52-P1-RACING-UNIVERSAL-DOUBLE-DECK-ALUMINUM-WING-SPOILER-SILVER-/180882091727?pt=Motors_Car_Truck_Parts_Accessories&fits=Model%3ABronco+II&hash=item2a1d69aecf&vxp=mtr
i was just reading in wiki. that the British were able to get 160 hp out of the 2.8 with fuel injection?
http://en.wikipedia.org/wiki/Ford_Cologne_V6_engine
this is on a 198 4 b2 with 2.8 durasparked
it seems when the outside temperature is below 32 degrees it over heats but when it is warmer then 32, like say today it is 65 out it runs in the r in normal even after i pushed it hard. i can only think fan clutch. but i dunno what to think. no...
I got a 84 b2 from my Pop he did a duraspark conversion years before he gave me this b2. it failed for a few things
1 i think the tech couldnt figure out the horn on the turn signal column
2 my pop had installed a edelbrock aircleaner on the carb he used and it dont have the Original...
when i pulled the transmission in Aug. my Neighbor helped me. he pulled off the lock washer on the shifter linkage for the transfer case and it got lost.
we installed evey thing with out it, but i would feel very much more comfortable if it was replaced. any ideas? this is all on a 1984...
http://mdc.mo.gov/zombies
Invasive Species Alert: ZOMBIES!
Welcome to this special Fresh Afield blog post.
Be warned of our state’s newest invasive species threat--ZOMBIES!
While zombie management is largely left to the police, military and health agencies, conservation plays...
you just need a Mr.fusion unit,flux capacitor, and time circuits now
http://inhabitat.com/the-electric-delorean-takes-riders-back-to-the-future/
http://inhabitat.com/all-electric-delorean-car-to-hit-the-streets-in-2013/
a 25 ft nema 6-50 extension cord for $116,064.41 :icon_surprised: imagine what you could buy equipment wise for welding for that..... no i am not looking to buy one of those but make them.
http://www.amazon.com/Anchor-SEPTLS1006019178806-Welder-Extension-Cords/dp/B002FCHG2Q/ref=pd_sxp_grid_pt_1_0
my pop gave me his b2 because its "rebuilt" transmission was going out again.
when i got it i heard a tappity, tappity, noise only when the clutch was let out. clutch pushed in it is quiet. my pop thinks its a input shaft problem and said it still is under warranty, pull it and bring it to...
hello, My wife picked up an old riding lawn mower, it is an upright engine and a 8 hp briggs and stratton model 190702, type 0674-01
it needs a new carb. or a good carb rebuild i cannot find parts on the net for it at all. so i asking fellow tinkerers to help please
i bought a decent air compressor recently. from my neighbor across the street
I learned after owning a crappy chinese welder and upgrading to a well made american hobart. i have made it a rule that tools i will use alot be well made and not chinese crap.
i dont care if it is new or not...
edit my title implies that the boys that are fighting are allowed to do stuff like this with out being prosecuted by liberal wienies
after hearing on how we dealt with Islamic lunatics in the past. by dipping bullets in pig lard thus sending the jihadi to hell for touching a pig before he...
on another ranger site i saw a guy who had to notch his frame a little to do a v8 swap. i thought i saw some stress fractures in his frame at the notch
what do you think?i wanted to warn him, but thought i run it by here first.
this summer i bought a house. well working outside i am trimming my bushes when i see one of my neighbors drive by in a i think 84 mustang svo. i think, cool.
over the summer i see him do peel outs and various stupid stuff with the car
and i just shake my head and go about my business...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.