Search results

welcome back, i find myself on here every now and again

i usually just use what i have laying around... they dont draw much.... i think it was 12g or 16g last time i bought some. also if you are installing it in a 2nd gen explorer they are plug and play..... the 1st gens might be to just havent pulled the dash to see, but all 2nd gens have the...

yeah there impedence is different, the older ecu can run them but if the MAF is even slightly dirty it will max the fuel trim out and run like a turd.

yup, ev6 plastics from a 2000 ranger in my 94 explorer, the ecm hates them but it runs

well i bought this 94 explorer(230k miles1 owner kept stock)/ rebuilt trans in the last 4 years), its driving me nuts. everytime the converter locks up in 3rd or OD on the highway(usually around 50-60 it starts) it get a nasty vibration under the seat and i can't figure it out. as soon as i...

go to albums, click on image, and click edit image go to corner of image and change to like 853 x 480(1024 might work to), i find if you type 853 in and keep the box check it will automatically adjust the size, then click save. no need to change your links, it will update the in TRS...

well i wanted a little more interior room and more seats than the ranger, so as the wife calls her Dora the Explorer #projectpurplebackpack the build has begun:yahoo: a 1994 ford explorer Eddie Bauer with 228k on her i picked up for $750 bone stock Not to bad for stock but i can leave...

does anyone have the pinout the 42 pin connector on the 2000 ranger 4.0 harness with the 5r55e and PATS?(might be close to the 5.0 harness in the 99-01 explorers) wondering how hard it would be to put into a 1st gen explorer for a project vs running the a4ld. that square one, i think it is...

as he said, dana 44ttb with 8 lug outers(from ford or chevy) to match the sterling rear axle. just stay away from the 87-88 dana 44 ttb, they have ranger style bearings/top hat lockouts unless you are going with the sterling(8 lug conversion) autofab use to sell a kit, not sure if they are...

http://www.pirate4x4.com/forum/ford/2132986-1994-explorer-superduty-one-tons-build-3.html only one i could find, been thinking of putting them under my ranger(the dana 60 version as its stronger, as the 50s have a smaller carrier/necked down shafts). the springs have to be outboarded though...

As title says thinking of moving out to the seattle tacoma area. What are the vehicle laws like out there I have a 02 f250 7.3 diesel and 00 ranger. Are there emissions? Will i have problems with my ranger running 35s/no bed?/ cut fenders? Can i remove the doors with no problems? Hows the...

any answer... My 2000 ranger just exploded on the driver-side my f250 did last year in the e-brake part(pin backed out) and a few years ago my buddy with a stock 2000 ranger 3.0 did the same thing.... i have even lost a tire on the D/S rear flat towing my old Bronco II:icon_rofl: ALWAYS...

looks like he is still running the ranger... http://www.safaripacific.com/2014/11/end-of-central-america-trip/

I am looking at picking a welder up in the next month or 2. Have any of you tried the hobart 210mvp mig welder? I was wondering if it was a good welder or not. Looking into it for welding some d.o.m. tubing and doing my own sas/fabrication. The 110/220v combo was a plus for me but wondering...

project Broken Ranger(more of a carnage thread than a build thread) picked up this 2000 ranger thursday welll here is the before Currentish more to come, :thefinger: need to install my 12k badlands winch and possibly my sliders. also picked up a mini spool for the 8.8 but idk if i am...

so i came across a complete 2000 ranger with the 4.0 OHV for a good price:headbang: xlt 4x4 extend cab etc. going to be picking it up at the end of the month and i have a 88 bronco with a pretty ruff body... on 35s 5.0 AOD, probably going to need a engine soon. i am thinking of fixing...

posted from fullsizebronco, though you ranger guys would like it. :icon_twisted: http://www.stangtv.com/features/car-reviews/project-spotlight-coyote-5-0-powered-ford-ranger-pickup/

80-96 f150/ bronco, just stay away from the 87-88, they have top hat hubs on them like the 35 and wont be a upgrade. i know because my 88 bronco i just bought has them

http://www.autoblog.com/2010/09/20/u-s-spec-ford-ranger-to-officially-end-production-in-2011-ford/?icid=main|main|dl4|sec3_lnk1|171681 :annoyed::sad:

my new tires/rims hankook atms 315/75/r16 Unique(crager) soft 8s 16x8 3" body lift 2" torsion twist being fitted bronco ii will be getting the old 265/75/r16 still indebate if i want to run adapter for 5x4.5 to 5x135 so they both are the same or get some exploder 16x7 rims