Search results

the charcoal canister I have has 2 ports for hoses a 1/4 inch that goes to the tank, and a3/8 inch for the purge . Tank is only vented to the canister. Should the purge line be tide in with the crank case vent?

Just finshed the head liner in my 89 ranger . the p. o. had let it set for 3-4 years and used it for storage stuffing it to the sealing . the head liner fabrce was sagging in several places and torn and golged into the form. The first thing was getting the form out after removing the seats and...

I need to find , or make a 20 amp circuit that is turned on/ off by the ignition switch. is there a good place to tap in for this power source inside the cab?

The back of the cluster has 2 14 pin plug ins that has only 1 pin not wired. This 1 is labeled v8. does this need to be grounded or does some other wire need moved?

Does anyone know the size hole that I need to make for the rear body mount? Is it 1.5" or1.75" THats on an 89 ranger ,what size hole for the front ones under the core support?

https://www.facebook.com/photo.php?fbid=572271902845226&set=pb.100001872656569.-2207520000.1385657303.&type=3&src=https%3A%2F%2Fscontent-b-ord.xx.fbcdn.net%2Fhphotos-prn2%2F1474485_572271902845226_599162606_n.jpg&size=960%2C720 what do you think?

Hey guys, it's Becca. I am currently thinking of doing a tailgate bench for one of my classes I am currently taking called Motorsports Fabrication. I have a dented and bent tailgate from my sister's '88 Ranger along with a few other bits and pieces left over from her wreck. I have a good idea...

Becca here, jmcleek's kid. Maybe you know the some of the answers to my questions. I would like to know what sizes wrenches to get for ac units in vehicles of all types. I'm going to Ivy Tech to get my degree in Automotive Technology and am learning on all sorts of vehicles. I would also like to...

I have used headers like these befour, and had problems with the 3 bolts that holds the exast pipe on falling out. what has every one been doing to avoyed this problem, double nutting them?:icon_confused: John

I am running a carb on my 302 in my 87 ranger and have come to the point that I need to deal with the charcoal canister sence the fuel tank vents to it. I am useing a Ederbrock 500 cfm with electric choke. How is other hooking this up to vacuum/ what sourse are you useing? Also getting ready to...

This swich keeps the fuel pump from running when the motor is not running / no OIl pressure, used on wire hot only hot in run/ start only. Anyone used one of these safty switches? Can they be teed in on one of the filter relocation lines? The oil pressure sending unit is in a tight spot and I...

Have installed the carborator, 1403 ederbrock 500cfm eletric choke, and working on some vacuum lines. I would like to know if any one has needed to use a vacuum delay valve, and what the part number is and has anyone needed to use any coolant controled such device?Has singal port vacuum advance...

Where is the best place to get the power for the electric chock for a carb on an 87 ranger? :icon_confused:

has anyone Used these fine lokar parts with a aod? instrutions http://www.sitelevel.com/click?url=http%3a%2f%2fwww.lokar.com%2fdownloads%2fpdf-instructions%2fford_aod_kd_kit.pdf&sid=2ccm8Y62SXVKJrA5 brackets http://www.summitracing.com/parts/lok-srk-4000/overview/ throttle...

I have some 31x10.5 r15 wheels that I am thinking of useing on my ranger . Have done the Explorer 8.8+ leave springe swap on the rear ,and it sits up nicely , how much of a lift would I need for the frount and where would I get It? Does anyone Know where to get new centers for stock ford truck...

What would be the least amount of space between a mechical fan and the radiator? John

Never could get the 2300 to run right ,so it out,7.5 rear is out, 5 speed mannal is out. 8.8 92 Explorer 4x4 rear end and springs is in ,87 Crown Vick 5.0 + a o d trans is in side note : drive shaft from 87 crown is 1" shorter than the stock ranger shaft so with a little fudgeing it fit...

I recently got a edelbrock intake for my 302/ 5l and was wondering what you would use on the gaskets ? I got mine used so it didnt come with every thing like the newone would have. here is the on line insructions http://www.jegs.com/InstallationInstructions/300/350/350-71211.pdf the...

I find that the dip stick tube comes up under the heater/ ac air box. is there a mod/ differnt tube that makes it easy to get to? John

I am switching from a 5 speed standard to a auto/ overdrive . Ijust want to dubble check that the 2 red/light blue wires on the cluch enterlock switch need to be hooked to the neutral safty on the transmisson