Are the gauges in an 08 ranger ran off the computer? I'm going to be swapping out my 95 ext cab for an 08 with the doors and would like to use the new gauges. Since I will not be running a computer AT ALL this may be a problem I suppose.
Im having a VERY hard time finding a v6 c4 or even c5 bellhousing. Does anybody know where I can get one? Ive tried all local and even a few distant wrecking yards and none of them carry anything older than 95.
I'm looking at a Hughes 4wd street/strip C4 and I'm going be getting one of there matching street/strip 2500 stall torque converters. My question is that they offer a 10.5 and 11.5 TC. What size will work on the 4.0 or 2.9 flex plate? I read the page stating whats need for the swap as well and i...
Really as much as i want to go with option 2 i dont have the spare coin to finish the truck and spruce up the rear end at the same time. its got a mini spool thats about it.
the main cap. It must have been fractured before i bought the rear end and while setting them up and torquing them down (yes i did them evenly) one snapped.
Why cant I find a set of new carrier bearing caps? Cracked one setting my third member up and cant find any replacements anywhere. Anybody any idea were to look?
Okay so I know the obvious difference in the two sets of gears but my question is.... I have 5.13's for my d44 front already and I want to drive my truck daily, in the case I would need 4wd say come winter time on the asphalt/hard surfaces would it hurt to drive in 4wd with 5.13's up front an...
Ok so on my search to find a 2.8/2.9 C4 bellhousing I have came across a 2.8/2.9 C5 bellhousing. So my question is this bellhousing the same as the C4? will it work?
Well I posted a couple of pics of my truck in the show section. Now its time to show some pics of my recent SAS in project second time around. The first few pics are my ranger with TTB and 6" lift and then 3/4 ton axles which I didn't like how it turned out. So long story short I went and...
Well I figured I would post some pics of my truck from when I first got it to now. Bought it flipped for $900, Its a 1995 4x4 XLT fully loaded with 4.0 and 5 spd on itand only 125,xxx. Put new roof and doors along with hood and drivers fender and grill with header panel. $1500 total in it with...
Has anyone extended the stock radius arms from the f150/bronco when doing there SAS? Here is a pic of mine. The main question is how will the cast radius arms hold up to my welded on extensions? Here is a pic 12" over stock. I still need to put ends on them and most likely going to plate where...
I have a 94 mustang gt with the 5.0 in it and a T5 5 speed. Reverse got blown out by previous owner. Heres my question.... I have a T5 from a v8 camaro are the guts the same as the ford T5?
So I have been searching fo awhile now and cant seem to find exactly what Im looking for. I have heard a C4 wil bolt up to a 4.0. Is this true and what all do I need? I have a 1994 4.0 motor. Will a C6 bolt up? what is needed to do either the C4 or C6? Lookin to build a pulling truck without...
What is the difference between the 1994 4.0 and 1995 4.0 gaskets sets? I have a 1994 block and heads that have been rebuilt but other than that everything else is 1995 stuff (intake, manifolds, assecories). Whats different between the kits?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.