Search results

Been a little while since I've been on here (a recent divorce will do the darndest things sometimes).. But I need a hand with something that should be a relatively simple task. When my CEL came on a while back I read the code (forget what it is exactly now) but it was to the effect my coolant...

Cold starting/driving has me at wits end ! I can't remember all the tests that I've done back in the summer but the TPS voltage checked out fine and I also replaced the that thingamajig to the left of the intake feeds air to the intake when at idle (I forget what its called now). Nothing has...

Fj7eVYqcXJE I'm not even sure where to begin.... (in the event the vid doesn't play..wouldn't in preview of post :annoyed:) http://www.youtube.com/watch?v=3gastk7-eJY

There are two tabs on either side of the front of the frame that have a bushing with a bolt going through it. They seem to keep everything together between the chassis and the rest of the truck as when they are loose and you hit a bump you can feel and hear the difference. I need to replace...

Ok here it is.. First off let me say thank you to all that information. The last time I looked into lowering the truck was about 12yrs ago and the only thing that was available to do it were spindles and were expensive at the time. I seen they're still available but I think I'm gonna go the...

I'm also thinking of rebushing everything.. would the beams eliminate having to do some of them? I'm not that familiar with what all gets replaced with the beam approach? And finally, with doing either the coil or beam route, are lowered shocks a requirement or just a good idea considering i'm...

Ok.. In my vision of lowering it.. not slamming.. I'm still looking at functionalities of a pick up but also have a better look and obvious handling characteristics that come with lowering the center of gravity, suspension travel, and so forth. I still, on occasion, utilize my bed for what it...

What about beams? Is that better than doing coils? What are the pros and cons if i may ask. I'm lookin at a 2-4 in my future

You think he would of found that Lurking!?! None the less he's right. This place is stocked to the rafters with information. Especially things like that. Now if you attempt something and have trouble.. Ask away as that's a different story. I myself am a little shy on coil cutting. Check the...

I was gonna throw a basic receiver on from Rock Auto. Not that I plan on towing anything.. It's that I could.. to the extent of a 2.3 that is. My question is did Ford prewire for the option? Is there a loom i can possibly find to wire up a harness or am i to just start butchering everything...

They say the older you get.. the more appreciation you have for things. That said.. I wish I would have done the right thing and be nicer to her. But I was 19 and well.. the rest is history. But now I'm 34.. and I feel sorry. No one.. including the wife, (except you guys of course) knows why...

Thank you. How do you figure out whats gonna fit nicely in the wells though. I got a new set of 225/60/16 on a set of '94 Mustang wheels that I'd like to keep if possible. 2 of the wheels had 55 series on which I put up front initially but they grabbed every single groove in the road and...

Ok.. if i do that do i have to change the shock mount locations as well? I think with dream beams you don't have to change the shocks or should that be done anyway? I'd like to get everything in order before i hand a shop the task at hand. Thanks for the reply btw. Dropping is foreign to me..

Getem up here!! (You can see my 4WD I loaded up in the rear.. works everytime!!) Oh and the resident polar bear

http://www.youtube.com/watch?v=ucmqERCOrQY

Had on Craigslist but thought I'd offer it to my fellow peeps. Brand new never used still in the box... Tired of wackin your CB antenna on things. Don't want anyone to walk off with it when you park? Then hide it!! Comes with all instructions and even the original FCC agreement as...

Thank you for the information. As fate would have it I put my winter wheels on this afternoon and noticed that my sping mounts don't look too healthy. Neither do my shock mounts. I should probably straighten that situation out first huh? They're a wee bit rusty.

So my new years resolution is to start of the spring with straight metal and paint. I then for whatever reason started thinking of a mild drop for it. But i have a Honey. And with that comes Honey Do Lists.. how would say drop blocks affect my payload capacity? I'm only looking at maybe a 2-4...

I know when i replaced the cat years ago the downtube was welded to it. My question is.. do they sell just the downtube from the header? My exhaust is 85% new (section of tubing after cat, new muffler and tail) but my downtube looks like hell. I did the channel-lock squeeze test and it held up...

:annoyed: There is a local speed shop that I've dealt with in the past and believe him to be a decent guy and who knows (especially fords) what he is doing. I walked in to inquire about putting a lock right in my 7.5. Mind you the man has a stock full of ring sets and lockers just sitting on...