This is my 87 ranger. I am wanting to get rid of the 17s that are on it and replace them with either weld pro stars or weld draglites if anyone can help id appreciate it alot i found a set of each locally and wanting to see if this can be done asap thanks guys
Well i switched from the little trucks to a 1979 ford F250. It has a 400m 4spd with granny low. Dana 70 back rear with 4.10s and a lock right locker. Its a Dana 44 front rear which I hope to be changing out in the next few months for a 60. It has a 6inch suspension lift with a 3 inch body and...
I know someone selling 2 slightly used rockford fosgate 10 inch subs hx2's
•dual 4ohm voice coil design
•CONsealer gasket hides mounting screws and provides airtight seal
•LXcursion basket features a deep step that keeps the spider from "bottoming out" and distorting your sound.
•frequency...
I have a 89 ranger that has a 5.0 HO motor in it with an aod. I am trying to figure out something to do for a shifter for it right now I just have the cable coming through the floor. I dont want to order a new one from jegs or anywhere like that cause they run about 200 bucks complete so im...
I have a 89 ranger that I put a 5.0 HO in. I have not ran the exhaust yet it is just headers as off right now. I finished up all the wiring and am ready to run the exhaust. I am not sure of how I want to run it yet I was thinking dual 2.25 inch exhaust putting a high flow round cat. in each pipe...
I have a 1989 ranger the truck was a 2.9 5 spd truck. I swapped in a AOD and a 5.0 HO out of a lincoln mark vii i have everything done but the efi wiring. I have the alldata EEC-IV module connector pin usage for the lincoln mark vii and the pin usage for the ranger. I also have the diagrams from...
Besides my 89 b2 with a 302 carbed motor im also working on this 89 ranger with a 302 out of a 88 mark vi I am trying to keep it EFI as it stands right now it has everything done but the computer wiring done. It has a AOD trans with a custom cross member the battery is secured to the frame...
I have been searching but have not found a direct answer. I am getting ready to do a EB44 swap to my 89 b2 in the next 2-3 weeks. I have a 302 under the hood so I was thinking about running Eb coils. I am looking to get 4-6 inches of lift probibly closer to 6. What size lift EB coils would I go...
Im asking HOW MUCH stronger it is then the D28 and how much stronger the D35 is then the D30. Also if anyone has done the swap before or has one how they like it and all that good stuff.
I was wondering how much stronger a Dana 30 solid front jeep axle then a D28. I currently have a D28 in my truck with a 302 and a C4. First off I hate TTB suspensions. I was thinking about doing a D30 swap mainly because its solid axle and I know its stronger then my D28. I know its not as...
My friend had a explorer that he parted out and it had a 8.8 in with disc brakes and 3.73s he knew i needed a rear so I gave him a hand stripping it all down and he gave me the 8.8 for helping him. My question now is besides haven to swap the spring perches, sway bar mounts, and put shock taps...
My fiance sold her saturn to get something different. She likes rangers and only has 2,000 to work with getting something and getting it put on the road. So anyway Ive been searching Craigslist for the past 3 days and I found a 1994 ranger that is an ext cab straight side 4x4 4.0 auto. the body...
Ok well here is the deal RumpRangerSTX, STRUCK, and myself have been talking and would like to organize a club. It would be something where we would do a scheduled meet at least once a month. Then if you want to meet up with other members inbetween the set once a month meeting/gathering you can...
How to tell a 8 inch diff from a 9 inch
Look at the lower nuts that hold the carrier (pumpkin or diff head) in the housing. Picture using a socket with an extension to remove these. On an 8" you can remove all of the nuts this way. On a 9" you can't get to a couple of the lower ones, the pinion...
I have a early 70's 302 in my 89 B2 It has a 670 cfm holly carb on it. It is a fairly stock motor with the exception of possibly having a small cam and it has a weind intake on it. other then that its stock right down to the points dizzy (will be changing that as soon as i get the extra cash)...
My new to me rig is a 1989 B2 that I got off of projectnitemare he is a great guy and great to deal with helped me out alot along the way of getting this
b2 off of him.
Its an 1989 B2 with a earlies 70 302 with a c4 trans and 13.50 tcase. It runs pretty good and shifts decent. I have only...
Has anyone attempted to go through the stability testing with anything that you did a motor upgrade to? Be it a 4.0 swap or a 5.0 swap or anything and passed or had any problems with trying it? I tried to call winslow inspection today but had to leave a message so figured id ask you guys here if...
Was going to post a pic of it up but my camera is dead. Anyway sitting on a level surface I measured from the middle of both wheel wells down. The front was 24 inches from the ground and the back is 25 1/4 inches from the ground. The front tire size is 196-65-14 and the back tires are 235-60-14...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.