Search results

Thank you Ron! I add it to my bookmarks!

Good afternoon Ron! I posted asking about my buddy's 91 rwd ranger that he bought a 2" lift kit all the way around and wasn't sure what size tire and wheel combo he could run after the lift whether 15" or 16" wheels. Do you have any experience on this body or what is the largest tire that will...

My buddy has a 91 ranger 3.0 rwd extended cab that he purchased a 2" lift (2" blocks for rear leaf & 2" blocks for front coils) and regarding tires and wheels what would be the best option. 15" or 16" and what size would be the largest to run without causing travel issues or rubbing when lock to...

It is a 8.8 with a 3.08 gear. I will add carrier bearing along with the pinion bearing to the check list. Thanks man

It is not a limited slip.

The issue with refilling is the attempting to get the bottle close enough to the vertical fill hole on the pumpkin. With the gas tank in the way it makes for a tough angle to directly refill. Regarding the noise, I replaced the U joints and the wheel bearings less than a year ago. I will put...

I have a 1994 4.0 2WD (manuel trans) that recently between 55-65 mph I start hearing a drone sound as if there is a semi truck getting close to me. It gets a little bit louder up to 75-80 mph. It doesn't get better or worse as I decelerate or accelerate. I am in the process of changing the fluid...

Sad thing is that I just put calipers and pads from Power Stop. They do bite down but not well as I had hoped for. I will keep that in mind for next time!

Agreed with the height of the truck making a difference. My reason / thought was that if or when you hammer on the brakes to stop quick, the front dips down slightly allowing the rears to have a greater chance of locking. With leveling or putting a little stiffer spring in the front, it might be...

I have a 94' 2wd super cab 4.0 with 10" drums. I had a near miss this past weekend (wreck) due the street being a little wet and my having to slam on my brakes to not hit the two idiots trying to dart out in front of me. I just replaced all components of my front and rear brakes excluding the...

Thanks guys!

Howdy folks, I have a 91 ranger that my buddy and I were talking about motor swap ideas. Other than the 5.0, will an eco boost v6 work? My thought is that with all the computer mumbo jumbo that it would need or take may not be worth it. Anyone have any other ideas that anyone has done? It seems...

I came across an engine hoist to lift/raise the engine enough to change my oil pan gasket. Question, what or where can I safely bolt the chain to (engine hoist) in order to lift/raise the engine? Also, am I correct in thinking that I should only have to unbolt the motor mounts and slowly...

I have seen a couple video's on L Oxide company that on Amazon, claims... "Oxide Reducing Emulsion to Restore Faded, Oxidized or Sun Damaged Car Paint, Peeling Clear Coat and Dull Headlights in a Simple DIY Operation. Easier to Apply Than Wax and Needs no polishing". There are video's...

My issue: In the truck, with the a/c on, and the truck has been driven for a little while, it will over heat (climb up to the "L" of normal). If the a/c is off, the truck will idle normal without overheating. Could this be a water pump? The radiator and fan clutch are new, the fluid is full...

I am in looking around for a pair of seat covers. I do not want to go with leather, nor am I working with a "Katzkin" budget. I found these covers which seem to be affordable as well as decent. They are from Realtruck.com / coverking neosupreme seat covers. Does anyone here know anything...

Howdy gang, I am looking to replace my shifter knob. Mine came off while driving (awkward). I am looking for a round ball style shift knob. Has anyone threaded theirs or have any how to's advice on this? Thanks for any helpful advise

1994 4.0l OHV, new heads replaced and running, upon test driving the truck it hesitates. I think (key word there) it may be O2 sensors (less than a year old motorcraft) or possibly a crankshaft position sensor (mine is a couple years old and a little dirty). Anyone have any ideas? Thanks in...