• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' the posts that you read.

Search results


  1. seat belt light on dash

    2019 Ranger XLT crew cab FX4. My seat belt light on the dash stays on. Anyone else run into this , or is there something i'm not seeing.
  2. How do you find what off set wheel you need .

    All ready have rough country 2.5 leveling kit. But for wider tires how do you figure the amount of off set you will need for the tire you chose. Never have used spacers not to sure about them. I won't my truck to be safe. Would you trust the tire store to know, most of them seem to just won't to...
  3. Midas

    Just like some thoughts on wheel spacers. I was at Midas the other day getting oil change and there was a guy there with a new ranger. I heard him say he had Rough Country 2 1/2 lift and some 2" wheel spacers on order and he was going to put wider and taller tires on his new ranger, like maybe...
  4. vapor lock

    Am getting my 1978 full size bronco up and running. It has the oem 351m and C6 in it. Driving it around today did real good till it got warmed good. run ok at low rpm but speed up some it would cut out like running out of fuel, i think it's vapor locking. Had a 79 F-150 with 351c do this years...
  5. warranty on 2019

    I have had a couple people say you have to be careful about up grades on the new 2019. That Ford can void your warranty if they won't. Would that just be your dealer, i could see this if you miss with the engine or computer. I bought the five year bumper to bumper warranty. Don't won't to miss...
  6. 4x4 light

    Have 1978 full size bronco, 351m & c6. Research tells me it's a full time four wheel drive. No locking hubs on front and shift pattern says it's NP203. It has a little blue light bottom of dash that is suppose to come on when in Lo Loc and when in HI Loc. where is the switch or sensor for this...
  7. used ECM

    on my 1999 4x4 ranger 3.0L manual trans. If i replace my ECM with one from salvage yard with same part number. Will it work or will it have to be reprogram. Don't have elec. door locks or elec. windows. Also replaced vacuum hub with manual hubs. Thanks
  8. PO141 and PO136

    1999 4x4 3.0L ranger, i have been dealing with a PO141 for a while now. I replaced 02 sensor after cat, i ohms tested the old one no resistance. The new one a bosch with around 3.4 or so, thought it was ok. but it's back and has the PO136 also. I had key on and got under it and with a test light...
  9. Serial / number

    1978 ford bronco, serial number tag is missing off door. Been sitting in storage for around 10 years. Having problems coming up with a title for it. Does ford put the serial number anywhere else on the body or on the frame. The guy i got it from don't know anything about it. Thanks
  10. underdrive

    looking for a set of underdrive pulleys for my 1999 4x4 3.0L v6 Ranger. In Odessa Texas-79763
  11. Door ajar

    Getting my butt kicked on a 2000 ford excursion. Working on my bosses excursion, replaced axle seals in front axle,and replaced all four door locks actuators. Was roar testing it and the door ajar light and dome lights came on. So i had no luck with wd-40, i pulled all six switches. One in each...
  12. clutch

    Hope i'm in the right form. My old 1999 ranger 3.0L 4x4 clutch is slowly given up. It's not a hot rod but do some playing in it. I put the manual type hubs on it , vacuum always a problem. Anyway is there big deal on what clutch kit to use. Or they about the same,what about slave cylinder. Are...
  13. NP 203 trans. case

    has anyone know of a video on the right way to work the NP 203 transfer case. I just got a 1978 bronco and it's the full time FWD by my research. On the shift knob it shows LO-loc - LO - N - HI - HI-loc. But all i can can feel is lo-loc all the...
  14. Pcm

    Dumb question about ECM & PCM. Is the ECM & PCM & ECU together in the one box. If you replace the ECM you replace it all, or is there another box somewhere.:icon_confused:
  15. engine dies

    I have a 1999 3.0 manual five speed ranger. the last few weeks for two or three times a week when i stop at a light or stop sigh the rpm drops real low and dies. it starts right back up. It doesn't do it all the time, it idles good at around 700 rpm. it runs good going down the road. any input...
  16. Fog Lights

    my 1999 ranger xlt 4x4 3.0 manual trans. Its don't have fog lights and i won't to add them. I got a bezel from ebay with switch, added no. 8&10 relays also fuse no.8 in dash and fuse 4 under the hood. problem is the plug ends behind the bumper are round and are set up for four pin. i have looked...
  17. vacuum 2.9

    This is most likely a dumb qustion. I was doing the sea foam test on my 87 4x4 2.9 yesterday. I used a can of spray in the intake to clean throttle body. then put 5.oz in the engine, it said 1.oz per quart of oil. Then i did the 3/4 can into the intake through the brake vacuum hose. But to my...
  18. frame

    hope i'm in the right forum.the rear frame is rusted real bad would like to replace the frame from back of cab to rear bumper. is the frames all the same on extend a cabs. and all the stander cabs the same would like to get a donor frame. are the 4wd frames and 2wd the same or different. my is a...
  19. high idle

    This is crazy,i went out back to start and run the old 87 ranger. I fired it up outside temp was around 98%. it started right up idled up to about 1200rpm, i gave it a little throttle and idle went up to 1500 and stayed there. i was going to kill it and check throttle cable, but when i pushed...
  20. 4x4 inter hub shaft

    hope in the right spot. I have been in tech articles on changing pvh to manual hubs. I have some a set of rugged ridge hubs off ebay $100. bucks. But what i would like to know is how much should the center axle shaft move. both move but it seems that the right front has more. Is the enter...


Top