• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' the posts that you read.

Search results


  1. 2000 Extended Cab XLT Seat Refurb

    I finally got tired of sitting like a hunchback in my truck while commuting and decided to be productive with some extra time off thanks to virus fears. My truck has also been read ended and the drivers seat hasn't ever been quite right ever since. I went to the local pull a part and went on the...
  2. Need ball joints, anyone know if these are press in or do i need control arm

    My 2000 2WD had replaceable uppers. I changed them when I did the lowers. Then a few months later, I did the control arm bushings...... So now I have rebuilt OEM control arms with way more hassle than just replacing the whole thing.
  3. Low compression and misfire.

    Good luck, I went through all the same on mine: https://www.therangerstation.com/forums/index.php?threads/head-swap-on-2000-3-0.177236/
  4. Heater core flush

    Cold weather finally made it this far south. I noticed the Ranger's heat was very lacking. I checked and changed the vacuum lines to the canister in the fender and to the heater hose shut off valve. Then I checked the blend door actuator and all was well with it. So I ran the truck and got it...
  5. Head swap on 2000 3.0

    Cold weather finally made it this far south. I noticed the Ranger's heat was very lacking. I checked and changed the vacuum lines to the canister in the fender and to the heater hose shut off valve. Then I checked the blend door actuator and all was well with it. So I ran the truck and got it...
  6. Injector replacement???

    Agreed on compression test: https://www.therangerstation.com/forums/index.php?threads/head-swap-on-2000-3-0.177236/
  7. Head swap on 2000 3.0

    The Ranger has been making 150 mile round trips for work every day right now. It is running regular unleaded with no pinging whatsoever. It has: 180 degree thermostat in it Intake coolant loop bypassed SCT tuner 87 octane performance tune on the computer OEM MAF Aftermarket smooth intake tube...
  8. Oddball size spare to match aftermarket rims

    I am running 225/70R16 tires on my truck on aftermarket rims. I dropped my spare today just to check it and it was low on air. I checked the date code which is "319" which means 31st week of 1999. so the spare is 20 years old. After looking around, the comparable 15" rim tire size is 225/75R15...
  9. 2001 running rich, no power, poor MPG’s

    Does it run more rough idling after its warm or after you run it hard?
  10. Photos of different wheel/tire sizes on stock and lowered 2WD's

    A while back, I was considering a set of Ford Flex rims for the truck, but didn't want to have to bore the centers or get spacers installed so I went with the American Racing rims pictured above. But they would have looked good:
  11. Cam Synchro - Not Exactly Accessible....

    If it helps any, this is the view of a new synchronizer installed in the correct position with the #1 cylinder at top dead center. Also, take a air gun and blow off the back of the block around the synchronizer before you remove it. Any dirt around there will fall in the hole as soon as you...
  12. New headlights on my 2000

    I had enough Amazon rewards built up to pick these up for free. https://www.amazon.com/gp/product/B008G23AUQ The reviews seemed good, and even if they don't last very long, I am going to take my time to sand and re-clear coat my OEM headlights to get them looking good again and keep them...
  13. 3.0 misfire cylinder 1 at idle when warmed up

    I had to do heads and head gaskets on mine at 180,000 miles: https://www.therangerstation.com/forums/index.php?threads/head-swap-on-2000-3-0.177236/
  14. 3" exhaust?

    Here is a clip of the above exhaust with a new dynomax replacement muffler just installed:
  15. What's the best cat back for decent sound

    I'm running the older version of this kit: https://www.summitracing.com/parts/wlk-17317/overview/year/2000/make/ford/model/ranger Along with the JBA shorty headers. I like the sound of it. I just installed a new replacement muffler today after almost 10 years, went back with the same dynomax...
  16. Dynomax exhaust muffler replacement

    Back in 2009, I installed a Dynomax cat back exhaust (WLK-17315) along with the JBA shorty headers and a tuner. The other day I got in the truck and as soon as I started it, I noticed the exhaust note was louder. I was heading to work, so I just went ahead anyway. Once I had some time at lunch...
  17. 3.0 Mystery Noise

    My 2000 3.0 Ranger has had a mystery noise for a while: _-cekrjAcPc Finally cured it with a new tensioner. You can see in the pictured how the belt was riding towards the front of the pulley on the worn out tensioner making it squeal as it was going onto the crank pulley. The belt being out of...
  18. Head swap on 2000 3.0

    Posted this over on the Fordtrucks forums. Here's the recap of my project. The breaks with the ~~~~~~~ are where it was different posts on different days: 5-16-2018 My 2000 2WD had been getting a worse and worse misfire over time. Add to that random codes for lean conditions and misfires on...


Top