• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' the posts that you read.

Search results

  1. Freshmeat

    1993 Ranger Battery Cable Question

    I think I’m going to connect it to the frame. Thanks for the help!
  2. Freshmeat

    Project Papa J

    This is about as cleaned up as it gets. I did perform a full glass service the other day. Debating on tint, but probably won’t ever get to it. ?
  3. Freshmeat

    1993 Ranger Battery Cable Question

    If I don’t get any good confirmation I’ll make it a frame ground. Just figured I’d see if anyone knows for sure. Thanks for helping!
  4. Freshmeat

    1993 Ranger Battery Cable Question

    Hey guys- I finally replaced the ground cable in my Ranger (1994, 3.0, 4x2, manual) with an OEM style replacement cable and there’s an extra ground coming off the lug at the block, but I didn’t have it on the generic cable that had been put in the truck before. Anyone know where it’s supposed...
  5. Freshmeat

    Project Papa J

    Made a bit of progress in recent weeks... We swapped out the 7.5” with 3.45s for a Ranger 8.8” with 4.10s. It’s open diff, 28-spline, and drums, but I’m fine with that. I don’t need 31-splines for a street driver and I’ll toss in a TrueTrac later for better traction in the yard. It’s the much...
  6. Freshmeat

    Project Papa J

    See if this works... I figure I’m well overdue for an updated pic... Between the new coils and the 31s it sits pretty much exactly how I wanted. I’m looking into leaf fitment to try to run a newer set of springs, but will simply replace the bushings in these if needed. Next move is to get the...
  7. Freshmeat

    Project Papa J

    So after doing some digging, the '95 unit is a lot "fatter", so it'll hit the air box on the '94. I'm not at all opposed to converting over to the '95 air box so I can run the newer overflow/washer bottle. Just need to catch one at the junk yard. It's been doing fine without the overflow so far...
  8. Freshmeat

    Project Papa J

    I saw that. My plan was to get to the yard when I see a 1995 pop up and see how it looks. I've got $20 that says I can make it work... and if not, I have a Hobart 220 that could assist with mounting. Haha
  9. Freshmeat

    Project Papa J

    Holy shit, man- that's good intel right there! Thank you for the lead!! I'm hoping they may have an overflow/windshield bottle, as I shattered mine putting it back in the other day. Oops!
  10. Freshmeat

    Project Papa J

    It runs!! Turned out to be the positive battery cable, as expected. It has a tank of really old gasoline (estimating 2 years) but it's actually running perfectly fine, so I'm going to run this down, then change the filter and put in some fresh fuel. Dropping the tank to clean it out is on the...
  11. Freshmeat

    Project Papa J

    I remember being in high school (6', give or take) and my brother, who had 3-4" on me... we would both cram into the jump seats in this thing to go places with my grandparents. These days, my wife won't even discuss the possibility of my 6yo sitting back there. Hahaha
  12. Freshmeat

    Project Papa J

    Diving into this all over again... Back in 2012 I rebuilt the top end with all new accessories (minus A/C), new clutch and hydraulics, and new brakes... and gave it to my dad for Christmas since it was his dad's truck... I had tracked down some 15" Explorer wheels that matched the original 14"...
  13. Freshmeat

    Bellhousing Bolt Size?

    I've had my 3.0 Vulcan motor sitting on the garage floor for about three years. Finally pulled it out to put it on the stand but can't find the bellhousing bolts. With a hurricane on its way I'd rather get it off the floor tonight just in case it does flood in my garage. Anyone know the...
  14. Freshmeat

    Any TN/KY/NC Members?

    I'm considering a move to Knoxville, TN. Anyone here in that general area? Curious about the lifestyle and industry in the area.
  15. Freshmeat

    Swap body or drivetrain?

    Soon I'll be tackling the task of swapping most of the drivetrain from a 4x4 '93 donor into my 4x2 '94 truck. Thinking about the engine crossmember and such... would it be easier to swap the bodies? Both are extra cabs so I'm not seeing why it wouldn't work. I know there's a lot of wiring going...
  16. Freshmeat

    Any difference from 93 to 94?

    Long story short, I'm looking at grabbing a 93 to drop the drivetrain into my 94. Can anyone think of a reason this wouldn't work? I know the slave cylinder changed at some point but figure I can use the 93 line also if needed.
  17. Freshmeat

    Quick Cylinder Head Question

    I know on most engines cylinder heads don't care whether they're on the left bank or right. I just want to confirm it to be true on the Vulcan 3.0. I cracked my right head at the exhaust flange. There's a '95 3.0 Ranger at the yard with the left side all stripped down. Just need to pull intake...
  18. Freshmeat

    Project Papa J

    My grandfather ordered his truck in 1993 as a 1994 year model truck. First year of Ford owning Mazda and he was so excited about all the great new things that would come of it. He was always very simple. It's a STX package with manual windows/locks, manual transmission, etc. I'm pretty sure the...
  19. Freshmeat


    I've been a member here for several years, mostly getting information for the random Ford trucks I've had. I'm back, this time checking up on information regarding a semi-restoration of my 1994 Ranger STX. The truck will never be sold and it has massive sentimental value to me, so before anyone...
  20. Freshmeat

    Will 4.0 t-case fit behind 3.0 transmission?

    I have a '94 Ranger 4x2 I'm thinking of converting to 4x4. If I can find a 4x4 3.0 transmission will it bolt to the case I have behind my 4.0/M5OD in the parts truck? Sorry for such a simple question that I could likely find if I was on a computer... this is just a little project that dropped...