Soon I plan on pulling my 1994 2wd Ranger apart and 302 swapping it. I plan on running a carburetor for a while so I want to remove all unnecessary wiring in the engine bay. I don't plan on using stock gauges or whatnot, I just need basic lights and the normal "body" wiring so the rest of the...
Well I go through cars faster than I change socks, I traded my NICE and clean '95 Ranger for a Bronco....then hydrolocked the bronco a week later. SO while I am doing some big work on that I bought a '93 Ranger 4cyl 5 speed for $600 and am going to play with it while DD'ing it.
Here's the old...
Here's my tow rig/winter beater.
1994 F-350 4x4 Crew Cab 8ft Bed. She's got the 351 and an auto but 4:10s help her on her way.
That's the only picture I have for now but we are doing a full but cost effective refurbish on her, exterior, interior and a good going through.
More updates as...
Yeah you're at approx 7" of drop, you need to add a notch to the frame. My 4" in the rear is as low as I would go without notching it, I bottom out on good enough dips in the road.
Dream beams and an axle flip are the way to go. I have them in my '95 and it rides like stock, definitely the way to go. It'll provide a 3/4 drop on a stock truck so maybe a 4/4 for you.
Ben
I want to make a topic for us lowered guys. It'll be a reference for checking out what tire/wheel size and combo will look like on the 2wd stock or LOWERED trucks (no lifted trucks please)
Here's the format I'd like to use, I'll do my truck as an example:
1995 Ranger, 3/4 drop, 205/70/14s...
Ok so a few weeks ago I bought my 2nd Ranger (8th vehicle I've owned and had registered since 2009)
She's a 1995 2wd, 4cyl, 5 speed with 99K. She's lowered 3/4 on dream beams and axle flip. Needs new rims/tires but otherwise is a very nice truck. I paid $1800 for her and hope to have a nice...
I just bought a Ranger! 1995 2.3, 5 speed lowered 5-6" and in my mind freaking sweet!
I'll post up more pictures tomorrow when I know more about it...lmao
Ben
Thanks for the comments guys, the truck has been amazing so far. No problems other than a little bit of death wobble from a loose bolt in the drop bracket.
Next project: RADIO
Ben
Ok so the Ranger started having some SERIOUS issues, so I unloaded it so I wouldn't have to put so much money into it that I was screwed. Then I went on the hunt for a replacement truck, had to be a Ford (or the right CJ) and preferably a Bronco.
I called a buddy of mine asking if he knew of...
Ok, so my Ranger is running on about 3cyl. Fuel problem because my gauge is showing 0-10psi at idle and at rev. I thought fuel pump and replaced it, no bueno. I'm ready to light the truck on fire, it takes all my money and breaks every other weekend.
Sorry for the rant. Any help?
Ok, I have a question. I heated up my axleshaft to help separate the u-joint cap so I could replace my 18yr old joints. Job went well and I will say there were no signs of problems. I went wheeling today and BOOM axleshaft broke at the ear where I was heating. Did that cause the axle to become...
I'll save the story on why and just leave it as "because I want to"...lol
So I want to run 37's with around 4" of lift, on my '93 Ranger 4.0 4x4 etc etc.
I need opinions on how to do it. I have a 4" kit that I'm going to be putting in soon (rough country with drop plate replaced with a custom...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.