• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Search results

  1. steven

    Lifting Options

    91 with James duff, add a leaf, 31x10.5, Does ride little stiff with Duff shocks but I don't wheel it.
  2. steven

    Rocker adjustment

    Having some valvetrain noise that I don't like on a 91 5.0 block, pulled valve covers to look and check things out. I adjusted the driver side scorpion rockers on the base circle of cam, moved over to passenger side and four of the lifters were not pumped up and would depress by hand. I know...
  3. steven

    1991 Ranger 1996 5.0 Explorer Swap

    I used Hedman 89500 for my swap, they fit good but I have GT40P heads and keep burning up plug wires. These headers should work great for non P heads.
  4. steven

    Beautiful 91

    https://www.autotrader.com/cars-for-sale/vehicle/718133151?city=Rogersville&endYear=2011&engineDisplacement=4.0-4.9&firstRecord=25&listingType=USED&makeCode=FORD&modelCode=RANGER&newSearch=false&referrer=%2Fcars-for-sale%2Fford%2Franger%2Frogersville-mo%3FendYear%3D2011%26engineDisplacement%3D4.0...
  5. steven

    1991 STX

    Figured would post some pictures of Ranger, 91 STX. Purchased unseen from George, rust free but needs repainted. Installed 3" James Duff lift and 31" BFG. Pulled 4.0 and installed 91 Mustang 5.0 and AOD with Advanced Adapters t-case adapter. Freshened up motor with new bearings, small Comp cam...
  6. steven

    SOLD! Torque monster 302 headers (small crack)

    Still Available? I will take them, 417-630-1177
  7. steven

    Temp and tach after v8 swap

    R Ron Ron, thanks so much for your help, spot on with the correct wires saved me alot of headaches. Have one more brain teaser, looking for the wire that would have went to the factory check engine light, would have ran from original ecm to dash light?
  8. steven

    Temp and tach after v8 swap

    I am needing some help with wiring or ideas, I swapped mustang 5.0 with Ron Francis harness in 92 ranger and I want to use factory gauges. First is temp gauge, I don't know which wire in engine bay that was hooked to gauge sending unit? I am assuming it entered in the cab on driver side. Wanting...
  9. steven

    5.0 revs at idle

    I have triple checked for vacuum leaks, and have replaced temp sensor and also ohmed it out and seems like it is good.
  10. steven

    5.0 revs at idle

    Looking for advice on mustang motor in Ranger. Have been trying to get it to run correctly for awhile with no luck, When I start it up it will idle up then drop down to 800 ish rpm and run for about a minute just fine then it revs up on it's own to about 1500 and stays there for about min or so...
  11. steven

    SOLD! 1991 ranger 4.0 motor and 5spd

    Springfield mo
  12. steven

    SOLD! 1991 ranger 4.0 motor and 5spd

    Pulling out motor and 4x4 5spd transmission to do 5.0 swap. Motor is reman from Jasper has about 35,000 on it runs great good oil pressure, no documentation on motor besides sticker on core support, purchased with no documents, motor is very clean, paint looks very good. Previous owner...
  13. steven

    Fuel pump questions

    So I am putting a 91 5.0 foxbody motor and trans in my ranger and have many questions, not sure if this is where I should post? Gathering parts and started pulling mustang motor and was wondering what kind of fuel pump I should put in tank. Truck is 4.0, Mustang motor has explorer upper and...
  14. steven

    Auto to manual hubs

    So wanting to swap out auto hubs to manual ones, will model 28 manual hubs work on model 35? I know I have to swap out the nut assemble...
  15. steven

    Transfer case options

    So ordered adapter to retain ranger tcase, got cam, explorer heads and intake on motor and just about ready to pull it out of mustang.
  16. steven

    Transfer case options

    Anyone ever try these eBay radiators on V8 swap...
  17. steven

    Transfer case options

    So I am having trouble locating an AOD 4wd output shaft, anyone have any suggestions?
  18. steven

    Transfer case options

    Anyone know a good source for output shaft and also adapter housing? Is that a wrecking yard thing?
  19. steven

    Transfer case options

    I assume with the 4wd output shaft and the correct adapter housing it will bolt to the back of the AOD. What output spline count is the 4WD shaft?

Sponsored Ad


Sponsored Ad

Top