• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Search results

  1. Just Plain Stupied

    Merry Christmas DG
  2. Just Plain Stupied

    Hey man, glad you're back. Sure been quiet here without you.
  3. 9" Swap

    So...how do I make sure I don't offset the knuckle too deep?
  4. 9" Swap

    https://www.therangerstation.com/tech/dana-44-knuckle-swap-on-to-dana-35/
  5. 9" Swap

    I've long ago given up on the idea of "cheap" for this build. Although I don't have unlimited funds, I'm willing to spend some money on it. I need this to be dead reliable, and Id rather not have to spend a lot of time wrenching on it after I get it where I want it to be. (other than...
  6. 9" Swap

    Thanks, I'll check it out.
  7. 9" Swap

    I didn't think of that before hand, but the idea came to me while I was at work today. I definitely wouldn't mind looking into custom shafts for the 8.8.
  8. 9" Swap

    Not at all into doing wheel adapters. I'd definitely upgrade the 9" if I go that way.
  9. 9" Swap

    I'm doing the D44 upgrade to the front. That's why I'd need the 5-5 1/2 for the rear.
  10. Wid Horses Wrap Trap

    I'm not all that unhappy with leafs. I'm not building a rock rig, and the expense of going linked and coil overs could be put into better components for the task.
  11. 9" Swap

    Who's done one? I tried searching, but coming up with zip. I've got a build going on an 89, and I'd like to do the D44 upgrade to the D35, which means I'll have 5-51/2 hubs. Gonna have to match it out back. Other ideas?
  12. Wid Horses Wrap Trap

    Thanks. I've already welded the axle tubes, and no lift blocks. I'l be using a new spring pack. I made the old one to haul/tow and it's stiff as a board without a lot of weight on it. This build is for more of an over landing rig, and I'll probably add auxiliary airbags if it needs help with...
  13. Wid Horses Wrap Trap

    Has anyone used Wild Horses Wrap Trap? https://www.wildhorses4x4.com/product/Wrap_Trap/bronco_rear_axle Thoughts? Results? Doing a V-8 conversion on the BII, and it's going to be a clean build. Plan to truss the 8.8 and looking at axle wrap options.
  14. Dana 20 ID

    No, it's a driver side drop. Jeep and Intl were both passemger side drop. I got a message that this is from a 66 (made in 65). Not sure why Novak doesn't list the B/M number.
  15. Dana 20 ID

    I just bought a rebuilt Dana 20 for a V-8 swap. It is a driver's drop so it has to be a Ford, but the B/M number does not match what I found on Novak for a Ford. So I'm stumped. The ser. is 661615 and the B/M 300529-3. Thanks for any help,
  16. Sticking GM parts onto my 4.0 swapped 86 (M62 supercharger install)

    I'm curious Have you seen any changes in how it runs when not under boost?
  17. Wanted Dana 20

    In search of a good (Ford) Dana 20 transfer case.
  18. Best 4.0 OHV intake

    Thanks. That's pretty much what I needed to know. I'll stick with what I have.
  19. Best 4.0 OHV intake

    Looking at starting a 4.0 OHV build for my BII. I'll be using the 4.0 out of my 98 Ranger. I'll be using new heads and rebuilding the bottom end and looking for options. The 98 has a composite upper intake, but it looks like from pics that there are aluminum uppers available for the 4.0. So...
  20. Relay ID...

    Nothing new under the Sun, I guess. I've seen these new digital engine management interfaces. Probably got exactly what I was thinking of just ready to plug and play. All I need is to get the digital chick that gives me directions to keep track of the operating systems while I drive.

Sponsored Ad


Sponsored Ad

Top