Search results

I am running this setup in the rear of the Fordzuki, and was running it in the front, but was popping birfs left and right, so I got chromos and decided to go easy on them with a lock right. This is after 3 years. Samurai diff, stock 3.73 gears, behind 6.5:1 sami case, and the pinto 2.3 (now...

I need to find a wiring schematic for a 97 Mazda B2300 ignition switch. I'm trying to swap the wiring over to the switch of an 83 Ranger, and have power and starter signal, but lose the power to the coilpack while cranking. I can't find any pins on the 83 switch that are hot both while cranking...

Took some pics of the shift rail plugs for the tech section, just to show location basically.

Haha. I know. I figured I'd ask though. I'm looking for an inline electric fuel pump to power the 97 2.3 with EFI in the LJ. Has anybody found one in a pinch that will work? I was wondering also about the high pressure pump from an 83-88 ranger, can I run just that, or do I still need the lift...

What is it? I'm trying to simplify a harness, and I'd like it to not be included. :D I'm shooting for a standalone engine/trans harness, so EVERYTHING else is getting tossed. And while I'm here.... I'd like to omit the instrument panel while I'm at it. I see one wire passing through that...

I have one I got for free, and thought about a million different ways I could put it under a ranger, but in all reality, the work you'd have to do to it, wouldn't make it worthwhile. They've got really tall and thin inner C's, weak balljoints, CAD, which means hubless, and IIRC, they're unit...

I'm getting close to needing an engine in the Fordzuki, and I've got a donor for it, a 97 Mazda with the 8 spark plug 2.3, with a m50d five speed behind it. The problem is, the trans won't fit in the zook, because it's longer than the tk4 that's in it now, and there is no room to reconfigure...

Your axle shaft, cut and splined, should run $50-75.

x2 I've never liked the front only locker for exactly that reason. Sure, the front helps pull you up over shit better, but not if it's broke. :icon_rofl: But as far as your question, I'd go chromos, with Longfield joints.:D , I haven't seen your current steering, but it'll probably work till...

We were headed out to Tahuya today, and ended up turning back because of the snow. So I gave a buddy a call, and headed over to his place for some backyard wheeling. :headbang: It started out all inocent like, crawling through a hole his son had dug, and playing around a little in the mud...

So what are your guys' thoughts on running an engine on ethanol and water? A diesel engine specifically. :stirthepot:

Project Ramzuki Well y'all know how it is. Once you start building, you can't stop with just one. :icon_twisted: The newest creation will be another Suzuki, this time it's an 83? Suzuki SJ410. I picked it up from a buddy who had been storing it at my house, and the longer I looked at it, the...

But if I'm not mistaken, weren't the YJ's passenger drop? It's gonna be more work putting in leafs than it would be to run coils and three link.

I've needed one around the house for awhile now, to move heavy stuff around the gravel lot out back, so I came up with this, pivots on the frame, and is controlled by the winch.

Will the Escort diesel engine bolt up to a TK4?

Yep that last one looks alot better. :icon_thumby:

What are the numbers on this tab? It's not a 14 bolt, obviously, cause it's got 10 bolts, 60s and 70s have 10 bolts, and should have the model on this tab here. As for the smooth housing. :icon_confused:

One thing nobody has mentioned, is if you go cutting and welding on your axle, you need to keep everything alligned. Something like this. http://www.pirate4x4.com/forum/showthread.php?t=306356 Other than that, I would cut the long tube down and use the rest on the short side. V notch the...

What are the key differences (if any) between a pinto 2.3 and a ranger 2.3? The only difference I've found in searching is the pinto motor is rated at 88 hp, while the ranger is rated at 79 hp. Are there any internal differences?

Agreed. A 44 isn't going to be much stronger than the yota axles.