Search results

I am just wondering why I see some 98 plus ford ranger 4X4s with factory skids plates. I dont see many but a few of them have the front aluminum skid plate.

Well the other day when i did my intake gaskets i noticed there was a small grey vaccum line plugged with a screw. I found out it goes to the heater control valve. I put it on and now i have no heat. But when i disconnect it i hear vaccum leaving the valve and then i have heat. What could be...

I have a 97 4.0 that has a problem after the vehicle has reached operating temperature. The idle drops and it will stall occasionally. When i notice the rpms go down i keep my foot near the gas in case it wants to stall. I have replaced the dpfe sensor,idle air control, and cleaned the mass...

Just wanted to let everyone know that the article in the tech library on where to put tow hooks is not good advice if you use them at all. This past fall i put them on the bracket which is also for your bumper like the article said. This metal bracket is also wayy thinner than the frame. Anyways...

well today i was looking around in the tech library and came across an article called gear indicator adjust/ repair. Ever since i bought my 97 last year the indicator has always been off to the right like almost one gear over. Kinda annoying. So i found out like the article said my adjuster was...

The other day i was looking around at a local pick n pull yard and came across a ranger with skjacker coils in like new condition.:headbang: So i had to have them and after some work i got them off. I paid $22 for both coils so i think i got a great deal.:icon_thumby: Put them in at school today...

Hey I am working on putting duals on my 97 Ranger 4.0. I am going with 2.5 inch cat back with 3 inch tips that are 18 inches long coming out behind each rear tire at an angle. I have bought 14 feet of pipe already and need to make a y pipe too. I am wondering how much pipe others have needed and...

I found some 15X8 rock crawler rims on craigslist with 3.75 backspacing. I have 31s that I would put on the rims. Will these rims stick out farther than my stock 15x7s?

I just bought a 1997 Ranger 4X4 ext. cab. I currently have stock 235 tires on it. I found a good deal on some 235 BFG muds brand new. I really want to go 31X10.5 but does anyone have this size on their third generation? Thanks

Hi I was wondering if anyone can give me instructions on how to repair the blend door. I just bought the new part. I cant find anything in the tech library.

I tried removing my mass air flow sensor today to clean it and I cant get the screws loose. They want to strip. How can I loosen them? Anyone have this problem?

How many rpms is the 4.0 OHV supposed to idle at?

Hi I am looking at getting a regular cab 1996 Ranger 2.3L 4X4 5 speed with manual hubs and on the floor 4X4. The truck has 188,000 on it and I am wondering if anyone has expierence with these trucks. I can tell it doesnt have much power but are the 2.3L generally reliable? What kinda gas milage...

I am looking at getting a 96 Ranger 4X4 with manual locking hubs. I tried the truck today. I locked the hubs and there is more noise from the front when driving even if i just leave it in two wheel drive with the hubs locked. I was just driving down the road. Is this normal? I know there is more...

I just sold my 2000 Mazda B3000 4X4 today. It was a good truck that was very dependable but I wanted more power. I do pull 12 and 14 foot boats fishing boats and with just 30X9.5 inch tires the engine could barely hold overdrive and on any type of hill forget it. I have always found when I turn...

I am looking at possibly getting a 1994 Mazda B4000 ext. cab 4X4. The truck has 189,000 miles on it and I know the clutch and transmission were recently replaced. This truck also has the manually locking hubs. I am just wondering if I should worry about anything from this year of ranger/mazda...

I have a 2000 Mazda B3000 4X4. I am wondering if I should remove my factory mud flaps. I have seen many trucks without them and I think they look better. I just have one problem if I remove them will the paint chip alot and will I get rust or alot of rust on my truck? I live in Wisconsin and in...