• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Search results

  1. Help me get crank pulley off

    Could you post a picture of the inside of the pulley with the puller removed ?
  2. Bronco 11 to 4.0

    After months of buying and finding the harnesses , guages , ecm, manual 1354 , steering column for manual shift for my 90 Bronco 11 I found this . 1991 Ranger 4.0 manual case and it runs . Was bought thru an estate , frame suppose to be bad . It was going to be junked . Couldn’t pass it up .!!
  3. Factory Ford wiring diagrams

    They run $19 I believe.
  4. Factory Ford wiring diagrams

    Faxonautoliterature has a lot of the factory FOMOCO wiring diagrams . Wasn’t sure where to post .
  5. Found! 3.73 D35 TTB

    I’m 4 hours away also . Got a 93 ranger and a 94 Explorer. Not sure of ratio in the Explorer . But Ranger is a 3.45 . Good luck .
  6. Found! 3.73 D35 TTB

    Have you tried car-part.com ?
  7. Bronco 11 length?

    Thank you . I’ve got the 90 ready to start putting everything out a 91 Ranger 4.0 to convert it to a 4.0 five speed . What’s a few more bolts !!
  8. Bronco 11 length?

    Per Ford specs , 1984 - 1988 are 158.3 inches long , 1989-1990 are 161.9 . Does anyone know where the difference is ? Mainly are the frames different ? Putting another frame under my 1990 , I have an 85 in great shape . Hate to go Tuesday and pick up a 90 if I can use mine . Thank You
  9. Wanted 2wd bronco ll rear sway bar 85?

    Measured all , 2 88 s , 90 , 85 and 86. All 3/4 .
  10. Wanted 2wd bronco ll rear sway bar 85?

    This is an 85 BR11 4 X 4 . Is this what your looking for?
  11. Cam gear bolts, crank bolt 4.0 OHV 1992

    Per Ford , E7RY-6A340-B replacement for the 2.8 , 2.9 , 4.0 crankshaft bolt .
  12. 4.0 manual swap done, starter grinding help

    Did you switch from auto to 5speed ? If you did , did you get the engine plate with the five speed set-up? The auto plate is different. Just a thought .
  13. Bronco II Leaf spring hangers.. HELP

    I will get out this weekend and do some rough measurements on a Ranger I picked up for parts . I got lucky and found a BR11 and got the front and rear brackets . Someone made the worst mess for A bracket I’ve seen . Right side set 1 inch further back .
  14. Can anyone identify this part? Looks like a Vacuum Container. This small hose broke off.

    It goes to that reservoir, leads to you hvac control for your vents for one .!
  15. 1994 Ford ranger core support

    Here are three supports I have . They are 91 ranger 90 BR11 and 94 Explorer . They are the same . Removing a lot including complete dash for my 90 .
  16. Bronco II auto to manual swap, M5R1/M5OD clutch cylinders?

    Changed several over like you . Everything is on the firewall. I used the 91 Ford ranger 4.0 clutch hydraulic system . The 88 has a weird pedal set up . You can find it but expensive. I used one from a 89 Bronco 11. A lot of customizing on the clutch pedal . Master cylinder bolts on , resovoir...
  17. 88-97 5spd transmission/manual transfer csae gear boot.

    I could use it . In the process of converting a 90 to 4.0 five speed . You take Pay Pal ? Zip is 42343 Thanks
  18. 2.9 Squirrel Damage

    I’ll check and get back , I have an 85 BR11 and a 85 and 90 Ranger out hear . Parts vehicles .
  19. 2.9 Squirrel Damage

    The Factory wiring diagram should tell what it is . I will try to check later . Which ever one it is it must need it . Can’t read any symbols on it .

Sponsored Ad


Sponsored Ad

Top