• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Search results

  1. Sasquatch_Ryda

    D60 difference

    Drivers side axle tube is a lot shorter on the 80's D60's and the pumpkin is offset to the drivers side more.
  2. Sasquatch_Ryda

    Narrowed 3/4 or 1 ton axles?

    Mine has a narrowed D60 front and Sterling 10.25 rear. Keep in mind the tires are 40x16r17 LTB's
  3. Sasquatch_Ryda

    I need some help IDing an ifs axle

    It is a D30.
  4. Sasquatch_Ryda

    Finally some options for the RBV crowd!

    Looks like NWF (North West Fab) is going to be offering an adapter that will allow the D300, NP205, Atlas, and their Blackbox Underdrive to easily mate to the Ranger, bronco and explorer transmission. Previously there was nearly no options available. Designed to fit in place of the BW1350 and...
  5. Sasquatch_Ryda

    Dana 60 sas ?'s

    Mine is narrowed. Still wider than stock width, but I narrowed it down. I used a 94 D60 for mine.
  6. Sasquatch_Ryda

    Kirbys 1991 Ranger Build Up and Solid Axle Swap

  7. Sasquatch_Ryda

    Kirbys 1991 Ranger Build Up and Solid Axle Swap

    I used a set from TeraFlex on my ranger
  8. Sasquatch_Ryda

    Ranger vs Garage

    Needed to tear down the small garage currently on my property to make way for my big shop that I am putting up. I was tearing it down by hand and got bored of that...soooooo https://www.facebook.com/photo.php?v=10154399475930144
  9. Sasquatch_Ryda

    legitimate question...please try and help me out.

    With stock leafs, a stock block and extended shackles my 91 sat level with a 5" front lift.
  10. Sasquatch_Ryda

    h9 axle description question

    I have not seen 80w90 in a ford rear end since before the 2000's. All 75w140. Either way....run 80w90 in it if you want. It isn't going to cause any issues at all.
  11. Sasquatch_Ryda

    h9 axle description question

    Not too sure about 3.88 gears....don't think that was every a possibility. It will be 31 spline. You're going to rock the full width?
  12. Sasquatch_Ryda

    best price for Dana 60s?

    Well....seeing as they can fetch $1000+ for complete axles...especially the high pinion ford balljoint and king pin axles.....grab em up. Minimum tire size for 1 ton gear would be 37's my friend.
  13. Sasquatch_Ryda

    Anybody ever use a Sterling 10.25?

    Either an 8 lug D44 or a D60
  14. Sasquatch_Ryda

    Anybody ever use a Sterling 10.25?

    40's with 5.38 gears and a Yukon grizzly locker Sent from my SGH-I747M using Tapatalk
  15. Sasquatch_Ryda

    Anybody ever use a Sterling 10.25?

    I got the width down to 61 1/4" WMS to WMS. They are around 65" stock if I remember right. http://www.fourwheeler.com/how-to/transmission-drivetrain/129-0506-ford-1025-1050-inch-axle-tips/
  16. Sasquatch_Ryda

    Anybody ever use a Sterling 10.25?

    There are a ton of lockers available for the sterlings.... I am running one in the back of my 91. It's narrowed roughly 4" using 2 short side shafts.
  17. Sasquatch_Ryda

    My 2002 Sport Trac

    So I sold my 97 Ranger that I was using for my daily driver a while back and picked up the 2002 Sport Trac. Being that I can't leave anything alone....here is how it ended up today Its got a 3" body lift, 2" torsion crank and extended rancho shocks, and rear shackles. I also swapped my...
  18. Sasquatch_Ryda

    U-bolts Question.

    A 2 wd without blocks.
  19. Sasquatch_Ryda

    Longer shocks after torsion crank

    Hey I've got the torsion bars cranked 2" on my sport trac and the shocks are now topping out over bigger bumps. Anyone know of a longer front shock other than the Rancho's listed in the tech library.....not a big fan of Rancho's.... Sent from my SGH-I747M using Tapatalk
  20. Sasquatch_Ryda

    looking for opinions about lockers and what not

    Yes Sent from my SGH-I747M using Tapatalk

Sponsored Ad

Sponsored Ad