Search results

'99 XLT with 2WABS, RWD, check engine light is on with occasional ABS. Speedometer still works but code is for vehicle speed sensor input. The ABS tone ring is fine, the wires all traced through leading to the PCM are not damaged, but after looking through some diagrams, it looks like the only...

What oil would you guys recommend for breaking in a 3.0L? its for a '99 XLT FlexFuel.

My '99 XLT 3.0 V6 blew a head gasket and now I'm replacing the engine. Upon disassembling just about everything to get it out, I had to evacuate my A/C system. Once I get the new engine and everything else put back, I need to recharge it. Now I went through the Automotive Air Conditioning 101...

could a failing abs module cause this? This truck only has 2 wheel ABS and tracing the wires led me to a connector that stays unplugged and capped at all times with the same corresponding colored wires to the differential mounted speed sensor. I changed the differential fluid not too long ago...

I replaced the fuel pump and housing assembly on my '99 FlexFuel and now it has a high idle. I bought the correct fuel pump assembly for the wheelbase and Flex Fuel option and now it gets stuck at a high idle whenever I accelerate. The bad thing is, if I DON'T touch the gas pedal, it idles so...

I traced the red/pink and black/green from the VSS all the way to the PCM and found no issues. I used a voltmeter to check for continuity throughout it all and there were no issues. I'm wondering if it is my PCM. I mean I'm hoping it's not. The only thing I did to it before even touching any of...

I have a '99 3.0V6 FlexFuel and my check engine light is on for a P0500 code. I have replaced the VSS on the differential but the code still remains. The truck has been sitting but there's no evidence of rodents or damage to the main harness. I am trying to trace the wiring to find the issue but...

Don't recall seeing anything about doing that BEFORE taking the needle off but thanks.

I replaced mine a while back with these from amazon: https://www.amazon.com/YITAMOTOR-Bright-Instrument-Cluster-Dashboard/dp/B01JRXI9IU/ref=sr_1_5?dchild=1&keywords=dash+led&qid=1613612650&sr=8-5 The ones for the MIL (malfunction indicator lights: check engine, ABS, etc.) SHOULD be these style...

So after seeing a how-to on removing the green film on the inside of the instrument cluster, I decided to do it and ended up getting all but the speedometer needle back to it's original position. The strange thing is also, now the needle "jumps" between speeds and sometimes gets stuck between...

After swapping from belt to electric cooling fan, the fan stays on even while the engine is off. I originally had the ignition wire from the kit spliced into the 50A ignition fuse in the engine compartment fuse box. Any suggestions on where to splice the wire on a "Hot in run only" location...

my '99 XLT FlexFuel 3.0 has lost it's merit and I want to swap it out. Swapping for something bigger/different isn't viable at the moment but would swapping to a newer generation of 3.0 be a bad idea? I know all too well these engines have issue and this is the original engine with 235k miles...

I've had, at least with my '99 XLT 3.0V6, cooling issues that led to warped (AL) heads with rough idle and miss-fires. I was told by several other owners this is also a common problem with certain years of the 3.0V6 Vulcan.

Nothing and I mean NOTHING in the junk yards. I live out in Arizona and plan on getting my A/C working again, on top of that, I've had cooling issues with it before. I figured a 2 (or 3 row like I got from Amazon) AL radiator would benefit everything and save me some mileage. I did also change...

So I have to change my Radiator (it's leaking slightly where the plastic meets the metal) and rather than dealing with another plastic/metal radiator I upgraded to an all aluminum one. Trouble is, it's three rows deep and there's no way it will fit with the belt driven fan. I was wondering if...

So my '99 XLT does not have a tachometer/RPM gauge, can I get a gauge cluster with it, from another ranger that actually has it, and just rig up a way to get it to work? Or will this just screw things up?

so I've noticed some play in my accelerator cable and decreased throttle response. The cable has some play in it and I think the springs are worn out (I have no idea how old the cable is), and I just want to replace it. I have the 2WD 3.0 V6 FlexFuel XLT model and would like to just replace it...

I noticed coolant escaping through my radiator cap recently. I was told it could be my head gasket or a bad radiator cap. It has 214k miles and the last engine overhaul was done at around 195k miles which included a complete gasket exchange, head resurfacing, and tune up. Since then, I have...

I own a '99 XLT with coil spring suspension and I have already changed the lower ball joints but I'm wondering if the upper ones are replaceable. I was about to buy some new ones but the listing says coil spring upper control arm "WITH replaceable ball joint". The thing is, the passenger side...

My '99 has had an interesting problem. The whole truck shakes when I start out in first and dwindles when I get into second, third, and so on. is it the friction disc worn out or the friction disc, slave cylinder and master cylinder?