• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Search results

  1. For Sale 1992 Tan Cloth Explorer Seats, Dash, Door Panel, Misc Interior

    I can take some pictures for you. Message me with your email address.
  2. For Sale 1992 Tan Cloth Explorer Seats, Dash, Door Panel, Misc Interior

    Tan Interior parts from a 1992 Explorer with cloth seats. Everything is in very good condition. front and rear seats front and rear door panels dash assembly sun visors rear carpet rear vinyl storage cover Pick up near Pinehurst, NC. $300
  3. OHV Valve Cover Replacement

    That is where I'm leaking on both sides. I noticed the valve covers don't have those little wings that spread out the pressure. I've got a set of those from another motor, so those will go in when I put in the new gaskets. Appreciate the advise.
  4. OHV Valve Cover Replacement

    My 1991 has leaky valve covers and I'd like to replace them. All the kits I see come with the upper intake gasket as well. So my question is do you HAVE to remove the intake to do the valve covers? Seems like a lot of work to replace something so simple. If so, makes me really appreciate the...
  5. Are Explorer Seats a Direct Swap into a Bronco II

    Looks like the rear seats are shaped different, but can they be used without additional modifications? If modifications are needed, what has to be done. Thanks
  6. For Sale NC: 1992 Explorer Gas Tank $50

    I have a complete gas tank assembly out of a 1992 explorer. Everything is included, pump, straps, skid plats, tank and some heat shielding. $50 Located near Pinehurst NC
  7. Hey, nice looking Ranger! I can help you with the pump and I'll check on those other parts you...

    Hey, nice looking Ranger! I can help you with the pump and I'll check on those other parts you mentioned. Interesting you mention the transmission. I have a M5OD on the floor I've been waiting to swap into mine, so maybe we can look to work something out on that.
  8. 4.0 OHV Crankshaft Pulley / Balancer Removal

    10-4, thanks for the additional info!
  9. 4.0 OHV Crankshaft Pulley / Balancer Removal

    roger that, thanks for the reply!
  10. 4.0 OHV Crankshaft Pulley / Balancer Removal

    I took off the center bolt and looks like you need to use a puller to get it off. I've seen a few different kinds of pullers and wanted to see what you guys recommend using.
  11. For Sale 1992 4.0 V6

    Sure, I just took everything apart. Sent you a message
  12. Where to Buy Dual Stick Shifter Boot

    It would be great to find the factory parts. I couldn't find any on Ebay either. With that said, that is a really good idea about making one with the blank plate and new boots.
  13. Where to Buy Dual Stick Shifter Boot

    I'm looking to swap a M5OD and 1354M into my Bronco II. Right now it has the manual transfer case but has the auto transmission. The explorer I pulled the transmission from had a push button 4WD, so it only has the single boot. Any clue where you can buy the dual stick boot and related parts...
  14. For Sale 1992 4.0 V6

    I will part out the motor as well and can ship parts if need be.
  15. For Sale 1992 4.0 V6

    I had picked up a 1992 Explorer to do the 4.0 swap into my 84 Bronco II, but decided to just stick with the 2.8 carb setup. The motor is pretty much as complete as you can get with radiator, hoses, fan. It has the front accessories with belt and exhaust manifolds all the way to the y pipe and...
  16. Duraspark Choke Setup

    Thank you both for the replies. The carb in the link you posted is like the one I have, so hot air choke with electric assist. I'll look to wire it up like you mention with an inline fuse. Regarding the hot air choke. Any chance you could post a picture of where on the intake manifold I need...
  17. Duraspark Choke Setup

    I'm looking to do a duraspark setup on my Bronco II. I found a NOS 1.08 2150 Motorcraft carb. The choke assembly has a place on the cover for a wire. Where does that wire come from? It also has a place on the bottom side that something is supposed to hook to it. It has a male/male connector...
  18. No Start

    Well, I got her up and running again! Turned out the negative cable wasn't tight where it attaches to the block. It was hooked up enough for the lights to work and for some current to get through, but not enough for it to start. Found that out when I bought a new negative cable to replace the...
  19. No Start

    Ok, I bought a Ford starter. Just put it in and same thing. I had my kid turn the key to start and I can hear/feel the click at the solenoid on the fender and also at the starter. The truck was running fine prior to this happening so I can't imagine how the motor could have locked up. Any...

Sponsored Ad


Sponsored Ad

Top