having an issue where the truck will not start. Cranks over just fine, I did check the fuel cuttoff switch, its not that.
I did go through a lot of snow today, I cleaned as much out as I could from the engine bay and had my truck running afterwards for about 45 minutes letting it melt/dry...
So, i've tried several shift motors I have, none of them shift the case far enough to engage 4wd.
i've also tried different 4x4 control modules as well. one combination (new CM old motor) gets it close, but its still not fully engages and slips out and bangs. Not good.
shifting the case...
Hey guys, so a couple months ago I was driving my truck around town, and while moving, it just lost forward drive and revved. So I lifted my foot, tried again, nothing.
Tried 1st, 2nd, reverse, OD on and off, nothing. Now, it does have a slight movement of the ground is flat and you Rev it in...
Posted this in my build thread, but may as well post here if someone's looking for a simple build.
Empty bed, cleaned it out and took some measurements.
Cut the plywood to length and width, then cut out the spaces for the bulges in the side of the bed.
First test fit to make sure the...
So here's my situation. Transfer case was rebuilt just before winter, put less than 5k miles since then. Transfer case is solid. And 4x4 worked great when I needed it during winter.
Fast forward to a few weeks ago...
When I switch into 4hi the light lights up in the dash, all good there no...
so a long time ago I did the chevy 64" leaf swap, went really well and I love the swap 100%
only issue is the ebrake cable bracket bolted to the front leaf hanger mount. now that it's been moved forward it obviously can't bolt to it. can I somehow move the mount on the cable further down the...
Hey guys, so my 2006 ranger is in need of a transfer case, and I don't have the time to try rebuilding mine on my own (i'll do it once I get a new one swapped in to learn)
But, finding a ranger transfer case is a pain, but I found a 1354 elec shift from a 2001 explorer 4.0 4x4. in theory...
1974 Ford Maverick
250 CI straight 6, 3 speed auto
White exterior, light blue interior
Re-dp brake system so it actually stops
Satin white paint, black hood stripes
Wheels (undecided as to what yet, but they will change)
So is there a special tool to remove the fan on the SOHC 4.0? Or is it just a large wrench? Needing to take the fan off so I need to know what to get, I don't have a wrench that large or a special tool so I need to know what I'm buying, thanks folks!
When I'm in 4x4 the system will clunk, and bang every few seconds and disengage periodically, but works fine other times. No I'm not on hardpack surface. this happens in mud, loose snow, sand, etc.
I replaced the U joint on the front shaft, it was a little worn but not bad. Issue still exists...
Hey folks. Looking to get a new computer. Decided to buy parts and build rather than buying pre built. Save money, and have better performance.
However I have no idea where to start. What works with what, and what the good parts are.
So I turn to you.
Budget. $700 +/- $50
Main use will be...
Hey folks, don't know much about v8 swaps, did a search came up with a few answers, just wanted to get some insight from folks who have done the swap.
Plan is to swap a 302 into a first gen, looking to find what I can get a 302 from that will make the swap the easiest, and have as little as...
Ok, so both rear signals and brakes weren't working as pointed out by a kind officer, so in bought new bulbs to replace. Right side first, bingo. Works now, on to left side.
No bueno. Didn't work. Do I tried a second, then third new bulb. No dice.
Any ideas? Checked the plug under bed, fully...
So I've had this idea for a while, and decided to Photoshop it and see how it would look.
It will be soft material, not hard fiberglass.
Sides will be snap on/off
And will be based on a tube roll bar that will eventually tie into a partial exo cage.
Just want some feedback on what you...
Just wondering if the two transfer cases have the same bolt to trans pattern.
Im thinking about tossing in an atlas 2 transfer case. And the one they make for the ranger/expo are a replacement for the older 1350. Bolts bright up. Now, I want to toss one in my 1354 equipped truck. Will it bolt up?
Alright, I'll start off by saying I know when to use 4x and when not to. So don't bother asking if I'm using it on pavement lol.
When I have my truck in 4hi (haven't tried in 4lo) I get a loud bang every few seconds when on the throttle. Some times when it happens it feels like I lose 4wd and...
After googling for a good hour and finding nothing, I'm making a thread.
Wondering what model year range of Toyota's have the steering box used in most ranger solid axle swaps.
Collecting parts for my swap and need to know what year trucks to look for.