• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

86 Bronco II... G-Unit


85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,195
Reaction score
17,503
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
Great stuff foam.

Closed cell so it doesn't absorb moisture.
 


Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,696
Reaction score
13,155
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,696
Reaction score
13,155
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,202
Reaction score
16,343
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.
Great stuff foam.

Closed cell so it doesn't absorb moisture.
Wouldn't that interfere with windows movement? Of course, that would give the door bouyancy. Handy for deep water crossings.

Seems like heavy sheet plastic from Lowe's/Home Depot/ Menards would do it. Fasten with thin double sided tape.
 

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,696
Reaction score
13,155
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
I was hoping for pre cut pieces...

Heavy sheet plastic would work though.
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,195
Reaction score
17,503
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual

snoranger

Professional money waster
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
RBV's on Boost
ASE Certified Tech
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Nov 25, 2007
Messages
13,053
Reaction score
13,524
Points
113
Location
Jackson, NJ
Vehicle Year
'79,'94,'02,'23
Make / Model
All Fords
Engine Type
2.3 EcoBoost
Transmission
Automatic
2WD / 4WD
4WD
My credo
I didn't ask for your life story, just answer the question!

RobbieD

2.9l Mafia
Joined
Aug 6, 2007
Messages
3,802
Reaction score
3,311
Points
113
Location
Georgia
Vehicle Year
1984,1990,1994
Make / Model
Ford
Transmission
Manual
2WD / 4WD
2WD
My credo
Toonces drives a Ranger . . . . just not very well.
Replacing or restoring the door liners are worth the trouble, IMO.

I use heavy plastic and stick the perimeter with spray glue. That works well for me, but butyl rope tape would be another option.

Ford used treated paper liners in the early models, changing to sheet plastic themselves after a few years.

I only use duct tape to reinforce around openings, or anything that sticks out. Tape will get wrinkly and janky after a while; cheaper brands do it worse.

94 Ex after.jpg


That's a '94 Ex door. Your older B2 should have a flapper vent that mounts in that lower rear rectangular opening.

I'm curious to hear how well the Coverlay door panels work for you.

Glad to see you back to beating on the beast.
 

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,696
Reaction score
13,155
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
Nice job @RobbieD

Seems I remember there being some butyl type adhesive used on these... I think my doors still have some remnants of that on them.

I see LMC has some pre cut mylar shields... $20 for the set. I thought I had found some cheaper somewhere but can't remember where.
 

RobbieD

2.9l Mafia
Joined
Aug 6, 2007
Messages
3,802
Reaction score
3,311
Points
113
Location
Georgia
Vehicle Year
1984,1990,1994
Make / Model
Ford
Transmission
Manual
2WD / 4WD
2WD
My credo
Toonces drives a Ranger . . . . just not very well.
Thank you, sir.

Yes, butyl tape was used on a lot of liners. Back when I was in 12 volt accessories, I was into a lot of car doors.

One pet peeve of mine, is hacked, torn or removed door liners. When work is done in a door, it's not that damn hard to properly remove and reinstall the liner.

$20 for a set of decent shields actually doesn't sound that bad.
 

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,696
Reaction score
13,155
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
You wouldn't have a recommendation for the proper butyl tape would you?
 

Shran

Junk Collector
TRS Forum Moderator
Supporting Member
Article Contributor
V8 Engine Swap
Solid Axle Swap
Joined
Mar 4, 2008
Messages
8,636
Reaction score
4,703
Points
113
Location
Rapid City SD
Engine Type
V8
Engine Size
5.0
I use the foil backed HVAC tape for door liners. Landscaping plastic works well for large areas.
 

RobbieD

2.9l Mafia
Joined
Aug 6, 2007
Messages
3,802
Reaction score
3,311
Points
113
Location
Georgia
Vehicle Year
1984,1990,1994
Make / Model
Ford
Transmission
Manual
2WD / 4WD
2WD
My credo
Toonces drives a Ranger . . . . just not very well.
You wouldn't have a recommendation for the proper butyl tape would you?
The regular gray stuff, like used in a lot of roofing / plumbing / household applications, will work but it's not real tacky, and tends to dry out after time. It's good to work with in case of removal and reinstallation.

The black, stickier stuff works much better to bond the liner to the metal, but can be difficult to remove later. In removal and reinstallation, it can get "stringy" but it resticks well. This was commonly used to install sunroofs back in the day, and one trade name was "Tacky Tape".

Imports used to use a white string of "goop" that was horrible. It used to "string" terribly when the liner was pulled off, and always made a hell of a mess.

The gray butyl tape really works OK, and is likely the easiest to find. If you have a auto body supply close by, a good counter man can probably recommend something that they stock that would work good to seal door liners.
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,195
Reaction score
17,503
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
I used butyl tape to reseal the back in my old F150. Parts store had it on hand.
 

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,696
Reaction score
13,155
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
I just ordered a set of mylar water shields from LMC. I guess I'll see when they get here if they're worth it.

Also got a roll of 1/4 inch butyl coming. I thought I might try the local parts store... they were nearly twice the money then having it just dropped at my door tomorrow.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top