• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' the posts that you read.

Recent content by wvcat

  1. How to cgange your rear spring shackles and hangers

    Since I was doing these I thought I would Submit a how to. First off the parts. I bought these kits off ebay. At 43.95 a side its way cheaper than ford and includes the bolts. Even though they are made in China(and I'm pro american) the Ford ones are definatley junk! Both sides shipped to my...
  2. How To Add foctory power doors

    Original Poster: John H. AKA wvcat Difficulty: 7 out of 10 Time to install: Approximatley 6-8hrs Disclaimer: The Ranger Station.com, The Ranger Station.com Staff, nor the original poster are responsible for you doing this modification to your vehicle. By doing this modification and following...
  3. Ranger 15 & 17

    I read posts daily but don't post alot. Just thought I'd share. As you can tell by my sig I have been messing with Rangers for a while. I bought number 15 rolled and did a body swap. The gold body I bought without a title and the truck had a reconstructed title anyway so I did a quick swap...
  4. Body swap/lowering question

    I'm not sure you can go by frame length, wheelbase would be more of a concern. Production 1983–1988 Wheelbase 107.9 in (2741 mm) 113.9 in (2893 mm) 125 in (3175 mm) Length 175.6 in (4460 mm) 187.6 in (4765 mm) 192.7 in (4895 mm) Width 66.9 in (1699 mm) Production 1989–1992 Wheelbase...
  5. Help this truck is ugly!

    I picked up this project truck and will be painting it soon, probably next week. I would like to keep some green (not likely to be the same shade)because of the jamms/engine compartment,... anything goes. I was thinking two tone with black over green or green over silver or green with stripes...
  6. Almost done pics...almost...new paint!

    Thought I would pic whore my new paint. I will be putting this up for sale within a week or so but its not a classified (mods please don't delete) If any ones interested pm me or email me at jph26047@comcast.net I still have a few little things to do but she's looking good!
  7. A few pics from today

    Brian and his girl Lisa, Scott, and I played with the trucks today...
  8. The Bronco2 they should have made

    Just screwing around with photoshopping....Somebody make one of these!!!
  9. Some new paint & some buffing!

    I finally got the project truck painted. Unfortunatley the paint didn't come out as good as I would have liked it. Usually I don't have to do much buffing but this time I either had to buff or repaint due to a few runs and orangepeel...#$@%$#@ As painted I use 1000 grit on runs...
  10. NEED HELP!!! 02 Ranger Airbags deployed! Replace What?

    On a 2002 truck the sensor is in the airbag controller under the center console, it will need replaced. Air bag deployment shouldn't cause it not to start. It could be the fuel inertia switch on the inside of the fiewall near the kick panel on the ps. There is a reset on it.
  11. Driveways full of rangers again..lol

    Just took a couple pics this evening. I'm tired of moving vehicles around...lol
  12. Picked up a hillbilly cadillac today

    wasn't sure where to post this... A lil wax and some window cleaner and she'll be just like new!!!
  13. Next-picked up another 2000

    I picked up this wrecked 2000 yesterday. Plans are to put it on an edge frame and convert it to 4wd as funds allow. The front is wrecked so I have to decide what year I want it to look like. Here is the only pick right now but I will add some more.
  14. Air bag question

    Does anybody know if I can use 2004 air bags with a 2000 controller? Even if you know where I can get information on air bags maybe I can find an answer. I want to use newer air bags for the newer look(plus I already have them) TIA John
  15. My current project 56k beware!

    I thought I'd show some progress on my project truck. Well I picked up this jewel with a good drivetrain, frame, and clean title. 4.0 5sp took the body off... Then I picked up this donor body(no title) then I swapped the body out I needed some parts so I hit certifit up trial fit them...