Recent content by Psychopete

can I have a calendar in exchange for the premium member sticker that never showed up back in like 2014? lol

I've been poking at this for a few days, I don't have any voltage between MAF RTN and SIG (terminals C & D). Terminals A & B check out OK - 12v and chassis ground. I tried another sensor and it's the same thing. My computer is setting 157 CM and KOER, KOEO is 111. Additionally it's setting a...

I've been working on and off on my '87 and decided to finally start a build thread. I am in the process now of still tearing it all apart. I work on it almost every weekend for a couple hours at a time, so this is going to take a really long time to get done. Here is my truck: It's was a...

Dodge slant 6 carburetor, non-EGR pre-73, real bad hesitation when taking it to WOT in park. Should I be able to see a shot of fuel from the accelerator pump looking down the venturi when throttle is taken to WOT? Seems like the accelerator pump is not working; the diaphragm rod seems to be...

I just bought a 1987 Ranger, and noticed the other day that there is a small crack in the windshield. I have a 1988 Ranger with a good windshield and have a shop that will install it for me. I would like to remove the windshield from the 88 to have put on my 87, is it true that I could get away...

There was an Arizona Ranger that came up for sale last year, CLEAN, but I missed out on the opportunity. Guy who owns it now told me last night he'll sell it to me for what he's got into it.... ($570) :D So I took my own advice and committed to buy the truck with the features I want. It's got a...

I have an engine to swap into my car, rear main leaked @ 140K, but wasn't that bad. The crankshaft has a groove from the seal riding on it. Can't make up my mind if I want to sleeve it. The original engine to the car has 188K and I changed the rear main to no avail. It still leaked between the...

They must be getting bored with Windows, looks like they are shifting over to Macs. :D http://technolog.msnbc.msn.com/_news/2011/05/02/6570126-malware-attack-specifically-targets-mac-users There's not a huge Safari crowd, but just a heads up. Don't know too much about Macs, but if you do use...

I have a machine at my house that I cannot get to connect onto the internet that I use as a development computer. I would just format it, but it is a lot of work to get everything back to the way it was. It all started with me buying a USB wireless adapter that didn't work under Windows 2000...

Those socks are metal. :headbang:

I bought a used Tempo that is in a lot better shape than my red one. Made a mistake when I bought it because it was leaking some trans fluid (pan gasket is leaking), but later I noticed it spewing oil onto my garage floor. Rear main; same problem with my Red one but this one is much worse. I...

Hello, I have a lawn boy that's had a slight knock, but always ran decent enough, but lacked power. It recently stopped starting, given what I knew, I decided to tear the engine down to see if it could be repaired cheap. It's a mower I got for free that leaked oil out of the oil fill spout...

PM Sent. :D I wish! Been on the todo list for a long time. So far only have rebuilt the original 2.9L, now 5.0L swap and some interior work. Needs body work and repainted, hope to get started on that this winter and finish the interior. This summer I just want to drive the thing...

I am curious if anyone has retained their stock fuel lines and found some (cheaper) female spring lock fittings to AN? Or other alternative I might look at for using the stock fuel lines? Retaining the EFI setup even though I am running carb, will be EFI at some point and don't want to wreck...

How many are running B&M shifters, and how did the install go? I didn't read far enough into the instructions before realizing that the shifter (Sport) would essentially need to be raised with washers from the floor to fit with the plastic outside box. I installed it right where I wanted it...