• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Why Did this Happen to My Front Brake WTF?


Angry Possum

No Fat Chicks, Truck Will Scrape
Supporting Member
Law Enforcement
Joined
Sep 18, 2021
Messages
594
Reaction score
471
Points
63
Location
Staten Island NY
Vehicle Year
1993
Make / Model
Ranger XLT SC
Engine Type
4.0 V6
Engine Size
4.0 OHV
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
N/A
Total Drop
N/A
Tire Size
235 75 15
My credo
Sometimes you eat the bear, sometimes the bear eats you.
I changed my brakes last week. 1993 Ranger 4x4 w 4.0. I heard a brake squeaking, I then smelled something burning.
Seems the outer break shoe support clamp broke. Huh. Why would this happen. It's Always something w me when it comes to doing brakes mice-elf. What did I F...g do wrong...These are decent brake pads too, Ceramic, I got them on Rock Auto.

20220612_165148.jpg
20220612_165749.jpg
 


Angry Possum

No Fat Chicks, Truck Will Scrape
Supporting Member
Law Enforcement
Joined
Sep 18, 2021
Messages
594
Reaction score
471
Points
63
Location
Staten Island NY
Vehicle Year
1993
Make / Model
Ranger XLT SC
Engine Type
4.0 V6
Engine Size
4.0 OHV
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
N/A
Total Drop
N/A
Tire Size
235 75 15
My credo
Sometimes you eat the bear, sometimes the bear eats you.
I'm looking at the Top Caliper Pin now, maybe that's why.. It doesn't look like it's in right.
 
Last edited:

Bgunner

Well-Known Member
Supporting Member
Joined
May 14, 2018
Messages
1,757
Reaction score
1,039
Points
113
Location
Western Mass.
Vehicle Year
1994
Make / Model
Ford/Ranger XLT
Engine Type
3.0 V6
Transmission
Manual
2WD / 4WD
2WD
Tire Size
225/70/R15
My credo
If it's not broken Don't Fix It!
Those pins only have a rubber center to them so they are apt to ware out at some point. Being the rubber goes through heat and cold cycles the rubber can deteriorate. From the looks of it the metal slides have become separated from the rubber or the rubber has collapsed letting the pin to shift. The pins are fairly cheap, or were, so replacing them is not that bad. I would pay attention to the heat that the brake is generating on trips to be sure you don't have a caliper hanging up.
 

Bgunner

Well-Known Member
Supporting Member
Joined
May 14, 2018
Messages
1,757
Reaction score
1,039
Points
113
Location
Western Mass.
Vehicle Year
1994
Make / Model
Ford/Ranger XLT
Engine Type
3.0 V6
Transmission
Manual
2WD / 4WD
2WD
Tire Size
225/70/R15
My credo
If it's not broken Don't Fix It!
After a look at the picture again the retaining clip for the brake pad is also broken. This hold the pad to the caliper and with the way it is now can allow the pad to shift and cause un even ware and damage to the rotor and possibly the caliper. If this is a pic of the new pads then I would get another set and just replace that one pad, for now. This could also, if the pad is leaning in, cause the rotor to heat up while the brakes are not pressed.

That has to be squeeking bad right now as the pad is hitting the center of the hub. It has already scored the rotor hub. this needs to be addressed ASAP. fix is a new pad on the outer side like I mentioned before.
 
Last edited:

19Walt93

Well-Known Member
Ford Technician
V8 Engine Swap
Joined
Nov 13, 2018
Messages
4,475
Reaction score
4,412
Points
113
Location
Canaan,NH
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
V8
Engine Size
351
Transmission
Automatic
2WD / 4WD
2WD
Total Drop
3"
Tire Size
235/55R16
My credo
If you don't have time to do it right will you have time to do it over?
The caliper pin is installed incorrectly as stated, but that didn't cause the pad to fall out. The tab on the pad wasn't securely in the caliper notch- I often have to squeeze them in place with pliers. Make sure you use silicone based grease on the caliper pins, petroleum based grease will attack the rubber insert.
 

rumblecloud

Well-Known Member
Supporting Member
Joined
Mar 6, 2020
Messages
1,385
Reaction score
1,106
Points
113
Location
48022
Vehicle Year
1994
Make / Model
Ranger Splash
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
1-1/2 inch front leveling
Total Drop
Stock
Tire Size
31/10.50/15
My credo
What's the worst that could happen?
angrypossum brake.png


Number 1 is what Bgunner is referring to that may be worn out. Number 2 is what 19Walt93 is referring to.
My first thought was that "the tab on the pad wasn't securely in the caliper notch."
So when you applied the brakes, the pad slipped completely out of the notch, hit the hub and split the retaining bracket. And that may have caused the pin to disfigure (or if it wasn't installed properly, it only made it worse.
 

JoshT

Well-Known Member
Supporting Member
V8 Engine Swap
TRS Banner 2012-2015
Joined
Aug 6, 2007
Messages
3,714
Reaction score
1,493
Points
113
Location
Macon/Fort Valley, GA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Transmission
Automatic
2WD / 4WD
4WD
IMO I thinks it's more likely that #1 started everything by causing the caliper to stick. Then #3 happened which allowed #2 to slip out of it's notch. Just my 2¢.

As for why #1 and #3 happened I can't say, but you are definitely at new pads and probably a new clip on that side.

Pad and rotor shown don't look that new, but it could be due to failure induced wear. I'd probably install new rotors and pads, and go ahead and replace all 4 caliper clips too just in case that was age related.
 

Shran

Junk Collector
TRS Forum Moderator
Supporting Member
Article Contributor
V8 Engine Swap
Solid Axle Swap
Joined
Mar 4, 2008
Messages
8,637
Reaction score
4,704
Points
113
Location
Rapid City SD
Engine Type
V8
Engine Size
5.0
My first thought was that "the tab on the pad wasn't securely in the caliper notch."
So when you applied the brakes, the pad slipped completely out of the notch, hit the hub and split the retaining bracket. And that may have caused the pin to disfigure (or if it wasn't installed properly, it only made it worse.
I would concur with this.
 

Angry Possum

No Fat Chicks, Truck Will Scrape
Supporting Member
Law Enforcement
Joined
Sep 18, 2021
Messages
594
Reaction score
471
Points
63
Location
Staten Island NY
Vehicle Year
1993
Make / Model
Ranger XLT SC
Engine Type
4.0 V6
Engine Size
4.0 OHV
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
N/A
Total Drop
N/A
Tire Size
235 75 15
My credo
Sometimes you eat the bear, sometimes the bear eats you.
I fixeded it it....Yes I broke that tab off. When I first put the brake on originally, i didn't put it on correctly methinks., And after I put the new pad on, the first time, I should of depressed the break to squeeze everything into place and hold it all together, which I didn't do. And yes the Pins were actually fine. The newer ones I purchased, didn't come with the rubber inside them like my old pins, So I used my old Pins. After I put the 2nd new pad into place, I pumped the brakes to lock it all into place. It's good now, thanks everyone. I do appreciate the responses. And yes, i used brake Grease on the pads and the piston.
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
7,991
Reaction score
2,794
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16

Angry Possum

No Fat Chicks, Truck Will Scrape
Supporting Member
Law Enforcement
Joined
Sep 18, 2021
Messages
594
Reaction score
471
Points
63
Location
Staten Island NY
Vehicle Year
1993
Make / Model
Ranger XLT SC
Engine Type
4.0 V6
Engine Size
4.0 OHV
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
N/A
Total Drop
N/A
Tire Size
235 75 15
My credo
Sometimes you eat the bear, sometimes the bear eats you.

Angry Possum

No Fat Chicks, Truck Will Scrape
Supporting Member
Law Enforcement
Joined
Sep 18, 2021
Messages
594
Reaction score
471
Points
63
Location
Staten Island NY
Vehicle Year
1993
Make / Model
Ranger XLT SC
Engine Type
4.0 V6
Engine Size
4.0 OHV
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
N/A
Total Drop
N/A
Tire Size
235 75 15
My credo
Sometimes you eat the bear, sometimes the bear eats you.
PS: Brake Grease in some local stores here is way too expensive.
 

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,709
Reaction score
13,165
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
The caliper retaining pin... probably worn before you even started doing brakes on the truck.... But it appears to be upside down... as Walt says. That pin has stops on one side. Those stops face up and get driven in until they hit the caliper bracket. I thought Ford recommended replacing the pins with every brake job. You can see the stops below...

1655154740398.png


Caliper grease? That should only ever be used on the slide pins.
 

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,709
Reaction score
13,165
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
I have to add another thing. In 40 years I've never once had to pump brakes to to get brake pads positioned correctly.
 

Shran

Junk Collector
TRS Forum Moderator
Supporting Member
Article Contributor
V8 Engine Swap
Solid Axle Swap
Joined
Mar 4, 2008
Messages
8,637
Reaction score
4,704
Points
113
Location
Rapid City SD
Engine Type
V8
Engine Size
5.0
I don't replace those pins every time but it is a good practice to do so. The little tabs on the end eventually wear out and the pins fall out completely, can't tell you how many 83-94 RBVs I've worked on that have missing clips. It's scary.

I have to add another thing. In 40 years I've never once had to pump brakes to to get brake pads positioned correctly.
I assume that he meant that he pushed the caliper piston in more than necessary and then had to pump the brakes to push the piston back out once everything was reinstalled...that is almost necessary on every disc brake job.
 

Sponsored Ad


Sponsored Ad

Members online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top