• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

wheel bearing issue?


Eddo Rogue

Well-Known Member
Joined
May 18, 2020
Messages
3,952
Reaction score
2,472
Points
113
Location
Burbank,CA
Vehicle Year
1993
Make / Model
Ranger 4x4
Engine Type
4.0 V6
Engine Size
OHV
Transmission
Manual
2WD / 4WD
4WD
Total Lift
skyjacker front leveling kit
Tire Size
31-10.50R15
My credo
Crossed threads are tight threads.
Not sure if correct category, but I found where my loose front end is coming from, but need help diagnosing whats bad.

When prying around, everything is tight except the front axle. The hub/rotor and outer wheel bearing is tight, but the inner wheel bearing seems to have play in it. You can see the axle wobble around inside the spindle. Would this cause my tire jiggle? I thought it was the ball joints, but they don't budge. I ordered Timken inner and outer bearings, races and seals. Am I on the right track?
 


ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,213
Reaction score
16,350
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.
Can you post a picture of where the play is? I think you're confusing some terminology. The inner and outer wheel bears hold the rotor onto the spindle. If it's 4x4, the axle shaft rides in a needle bearing in the back of the knuckle.

Does the wheel wobbly around?
 

rumblecloud

Well-Known Member
Supporting Member
Joined
Mar 6, 2020
Messages
1,385
Reaction score
1,106
Points
113
Location
48022
Vehicle Year
1994
Make / Model
Ranger Splash
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
1-1/2 inch front leveling
Total Drop
Stock
Tire Size
31/10.50/15
My credo
What's the worst that could happen?
This bearing?

20220117_145610.jpg
 

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,213
Reaction score
16,350
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,213
Reaction score
16,350
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.

Eddo Rogue

Well-Known Member
Joined
May 18, 2020
Messages
3,952
Reaction score
2,472
Points
113
Location
Burbank,CA
Vehicle Year
1993
Make / Model
Ranger 4x4
Engine Type
4.0 V6
Engine Size
OHV
Transmission
Manual
2WD / 4WD
4WD
Total Lift
skyjacker front leveling kit
Tire Size
31-10.50R15
My credo
Crossed threads are tight threads.
Can you post a picture of where the play is? I think you're confusing some terminology. The inner and outer wheel bears hold the rotor onto the spindle. If it's 4x4, the axle shaft rides in a needle bearing in the back of the knuckle.

Does the wheel wobbly around?
You might be right....yes the wheel wobbles around with the lug nuts tight. Not much but enough to worry. I'll try to post a pic. There is play in the back of the knuckle. The rotor itself is tight. Im scratching my head a little at it.
 

19Walt93

Well-Known Member
Ford Technician
V8 Engine Swap
Joined
Nov 13, 2018
Messages
4,475
Reaction score
4,412
Points
113
Location
Canaan,NH
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
V8
Engine Size
351
Transmission
Automatic
2WD / 4WD
2WD
Total Drop
3"
Tire Size
235/55R16
My credo
If you don't have time to do it right will you have time to do it over?
We had a ton of trouble with spindle bearings in the 80's and into the 90's, mostly F series and Broncos but Rangers too. If you hit a bump driving with the hubs locked, it would sound like you were driving on scarified pavement. You should definitely replace the seal, too, and look carefully at the bearing surface on the axle flange.
 

Eddo Rogue

Well-Known Member
Joined
May 18, 2020
Messages
3,952
Reaction score
2,472
Points
113
Location
Burbank,CA
Vehicle Year
1993
Make / Model
Ranger 4x4
Engine Type
4.0 V6
Engine Size
OHV
Transmission
Manual
2WD / 4WD
4WD
Total Lift
skyjacker front leveling kit
Tire Size
31-10.50R15
My credo
Crossed threads are tight threads.

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,213
Reaction score
16,350
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.
You might be right....yes the wheel wobbles around with the lug nuts tight. Not much but enough to worry. I'll try to post a pic. There is play in the back of the knuckle. The rotor itself is tight. Im scratching my head a little at it.
The spindle bearing does NOT support the wheel. It only supports the axle shaft and keeps it centered where it passes through the spindle, which is bolted to the knuckle. The wheel bearings support the wheel. If the wheel wobbles, then the wheel bearings are either loose or worn out.

There is a procedure for tightening the wheel bearings. I don't recall the exact torque values at the moment, since I usually do it by feel and, with 35" tires, I have found that mine needs to be just a tiny bit tighter. But, basically, when assembling, you tighten the bearing nut to around 20 or 30 ft-lbs as you rotate the rotor. Then back it off a full turn. Then snug it up to about 17in-lbs. Install the washer with the oil to keep the nut from rotating. Then tighten the lock nut to 150ft-lbs to keep everything in place. Notice the change in units on the second torque value - in-lbs, not ft-lbs.
 

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,213
Reaction score
16,350
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.

rumblecloud

Well-Known Member
Supporting Member
Joined
Mar 6, 2020
Messages
1,385
Reaction score
1,106
Points
113
Location
48022
Vehicle Year
1994
Make / Model
Ranger Splash
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
1-1/2 inch front leveling
Total Drop
Stock
Tire Size
31/10.50/15
My credo
What's the worst that could happen?

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,709
Reaction score
13,165
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
Maybe the spindle is loose...
 

Eddo Rogue

Well-Known Member
Joined
May 18, 2020
Messages
3,952
Reaction score
2,472
Points
113
Location
Burbank,CA
Vehicle Year
1993
Make / Model
Ranger 4x4
Engine Type
4.0 V6
Engine Size
OHV
Transmission
Manual
2WD / 4WD
4WD
Total Lift
skyjacker front leveling kit
Tire Size
31-10.50R15
My credo
Crossed threads are tight threads.
Sorry guys, I meant knuckle not spindle, or whatever its called here....Its a dana 35 TTB. I think 31 spline. Good info here.
So in conclusion, what bearings should I change in total? I'd rather not replace one bearing in a system anyway...
 

Eddo Rogue

Well-Known Member
Joined
May 18, 2020
Messages
3,952
Reaction score
2,472
Points
113
Location
Burbank,CA
Vehicle Year
1993
Make / Model
Ranger 4x4
Engine Type
4.0 V6
Engine Size
OHV
Transmission
Manual
2WD / 4WD
4WD
Total Lift
skyjacker front leveling kit
Tire Size
31-10.50R15
My credo
Crossed threads are tight threads.
I already ordered inner and outer wheel bearings (and seals), what else should I order?
 

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,709
Reaction score
13,165
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
Pizza... beer... and maybe a Russian bride
 

Sponsored Ad


Sponsored Ad

Members online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top