• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

92 4x4 3.5 in lift


sumncguy

Member
U.S. Military - Veteran
Joined
Dec 14, 2016
Messages
98
Reaction score
18
Points
8
Location
Hillsborough NC
Vehicle Year
1992
Make / Model
Ford
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
at least 6"
Tire Size
32x11.5x15
Picked up this truck to do jobs around the house.. pick ups etc.

The lift to me is a little extreme but I dont really care. What I do care about is getting rid of those silly mud tires.

I'd like to go to a steel rim and road all terrain tire.

I've had plenty of 4x4s before but none jacked up like this.

My question is
How do I work backwards to figure out a rim and tire size ? A tire that doesnt necessarily have to be 33 high but should still look ok given the lift .. and that certainly doesnt need to be so aggressive ... a road all terrain would do.
20200912_104528.jpg
20200912_104528.jpg
 


SenorNoob

Well-Known Member
TRS Event Participant
Joined
Oct 24, 2012
Messages
2,348
Reaction score
520
Points
113
Location
Middle Tennessee
Vehicle Year
1988
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Total Lift
1.5" Front + 4" Rear
Tire Size
245-70-R16
Before you get new tires, get an alignment or DIY. That's serious camber induced wear.

Also post up some pics of the front and rear axles. May have more than just a lift. Never really know what someone else did.

Edit: Tire Size Calculator
 

Elutheros

Active Member
Supporting Member
U.S. Military - Veteran
V8 Engine Swap
Joined
Jul 11, 2011
Messages
660
Reaction score
129
Points
43
Location
Central Texas
Vehicle Year
1992
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
2WD / 4WD
4WD
Good looking -92!
 

sumncguy

Member
U.S. Military - Veteran
Joined
Dec 14, 2016
Messages
98
Reaction score
18
Points
8
Location
Hillsborough NC
Vehicle Year
1992
Make / Model
Ford
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
at least 6"
Tire Size
32x11.5x15
Yep. Ofcourse. I'm an old guy 57.
Turns out the wheel bearings were in bad need of adjustment and the stabilizer shock was missing bushings. Got that done then the alignment.

But these 12.5 wide muds need to go.
Was thinking a plain Jane black steel wheel and a/t's. Maybe 31x10.5x15.

What do you guys think ? Dont want the truck to look stupid given the lift ... but those 12.5s got to go.
 

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,213
Reaction score
16,350
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.
But these 12.5 wide muds need to go.
Was thinking a plain Jane black steel wheel and a/t's. Maybe 31x10.5x15.
I think thats a fabulous plan.
 

Uncle Gump

Token Old Guy
TRS Event Staff
TRS Forum Moderator
Supporting Member
VAGABOND
TRS Event Participant
Joined
Sep 17, 2018
Messages
13,709
Reaction score
13,165
Points
113
Location
Ottawa IL
Vehicle Year
2006/1986
Make / Model
Ranger/BroncoII
Engine Size
4.0L SOHC/2.9L
2WD / 4WD
4WD
My credo
Lead follow or get out of my way
I honestly think a 31 inch tire is to small... you should spend a few minutes also to figure out your gear ratios. If it has good shift points on those 33's I would probably stay with 33's. But I would go with a 15x8 in wheel and do 33x10.50x15 tires... there are still a couple brands out there in that size. BFG makes them in an all terrain.
 

scotts90ranger

Well-Known Member
RBV's on Boost
Joined
Feb 28, 2001
Messages
7,936
Reaction score
4,231
Points
113
Location
Dayton Oregon
Vehicle Year
1990, 1997
Make / Model
Ford
Engine Type
2.3 (4 Cylinder)
Engine Size
2.3 Turbo
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6
Tire Size
35"
That and more back spacing, sticking out that far on a Dana 35 is just asking for wheel bearing issues... I've had very little wheel bearing issues in the 10 years I've been running 35"x12.5 tires, but I'm running neutral backspacing (probably 4", don't know or remember, I got the wheels 10 years ago used) 15"x8" wheels
 

sumncguy

Member
U.S. Military - Veteran
Joined
Dec 14, 2016
Messages
98
Reaction score
18
Points
8
Location
Hillsborough NC
Vehicle Year
1992
Make / Model
Ford
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
at least 6"
Tire Size
32x11.5x15
That and more back spacing, sticking out that far on a Dana 35 is just asking for wheel bearing issues... I've had very little wheel bearing issues in the 10 years I've been running 35"x12.5 tires, but I'm running neutral backspacing (probably 4", don't know or remember, I got the wheels 10 years ago used) 15"x8" wheels
I have zero experience with this kind of thing. I bought this truck to do work around the house, bring garbage to the dump and pick stuff up, let's say, like new appliances or furniture. I live in the country of NC. Basically it will serve as my clunker workhorse. I have my Street Glide and Civic otherwise.

I got this truck for a song.
There are 2 things I'm trying to resolved

1. Tranny and 4th gear. Have 2 solenoids, vacuum modulator and tune up kit in hand. If that doesnt fix my issue I have a used a4ld auto 4x4 with 87k on it in line for $350. Some of the guys here gave me a few things to try. I was going to do this myself... but when I found out the valve body had to be dropped .. I just dont want to mess with that maze .. pucks springs and bearings. Getting a trusted tranny shop to do it for me.

2. Steering. This is where the tires and rims come in. Its sloppy as hell. Adjustment of the steering gears helped a little but still way to sloppy.
So i did what any wanna be mechanic would do. (Actually I can wrench a bit .. but I pick what I want to do. Lil Lazy)

I crawled under and started to poke around. I found that one of the sway bar links was loose. I mean I could spin the nut and bolt freely with my hand. That bushing is shot. All the sway bar bushings should be here tomorrow. I'll be doing all the easy bushings and boots up front a little at a time leaving the pita's for a real mechanic to do.

Part of getting the steering under control is to bring the rims and tires back down to reality. I don't want to spend the money on dropping the truck.

What I do want to do is to get a steel rim that "belongs" on the truck and a narrower non mud tire.
This should help a bit with steering ofcourse in conjunction with any needed front end work.
So I'm open to keeping a 33 on there .. but not sure about backspacing and offset .. just want a direct fit steel rim that will work.

Please let the suggestions fly .. I'm all ears

Thanks for all the help fellas.

.. and how do I get that military banner ?? U.S Navy 81 to 86.
 

MikeG

Well-Known Member
Joined
Jul 15, 2020
Messages
1,353
Reaction score
752
Points
113
Location
central Texas
Vehicle Year
1997
Make / Model
B4000
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
2"
Tire Size
235/75r15
I-beam bushings are probably shot. When that happens, you don't steer the truck, as much as you sorta herd it in the direction you want it to go......
 

snoranger

Professional money waster
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
RBV's on Boost
ASE Certified Tech
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Nov 25, 2007
Messages
13,055
Reaction score
13,529
Points
113
Location
Jackson, NJ
Vehicle Year
'79,'94,'02,'23
Make / Model
All Fords
Engine Type
2.3 EcoBoost
Transmission
Automatic
2WD / 4WD
4WD
My credo
I didn't ask for your life story, just answer the question!
.. and how do I get that military banner ?? U.S Navy 81 to 86.
It’s added automatically when you fill out your profile info and click on “US military - veteran”... I took care of it for you.
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,213
Reaction score
17,528
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
Sway bars won't effect steering, some people flat out remove them for more articulation and get along ok.

Check for play, all the joints in the linkage and the steering box. Also check the rag joint (and u-joint) in the stub shaft between the firewall and the steering box. And where that shaft connects to things, when I first got my truck it was loose between that stub shaft and the steering shaft that goes into the cab.

A little bit of play goes a long ways in the steering box though.
 

sumncguy

Member
U.S. Military - Veteran
Joined
Dec 14, 2016
Messages
98
Reaction score
18
Points
8
Location
Hillsborough NC
Vehicle Year
1992
Make / Model
Ford
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
at least 6"
Tire Size
32x11.5x15
I-beam bushings are probably shot. When that happens, you don't steer the truck, as much as you sorta herd it in the direction you want it to go......
That pretty much it ... I'll look them up. Thanks
 

sumncguy

Member
U.S. Military - Veteran
Joined
Dec 14, 2016
Messages
98
Reaction score
18
Points
8
Location
Hillsborough NC
Vehicle Year
1992
Make / Model
Ford
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
at least 6"
Tire Size
32x11.5x15
It’s added automatically when you fill out your profile info and click on “US military - veteran”... I took care of it for you.
Thank you !!
 

sumncguy

Member
U.S. Military - Veteran
Joined
Dec 14, 2016
Messages
98
Reaction score
18
Points
8
Location
Hillsborough NC
Vehicle Year
1992
Make / Model
Ford
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
at least 6"
Tire Size
32x11.5x15
Sway bars won't effect steering, some people flat out remove them for more articulation and get along ok.

Check for play, all the joints in the linkage and the steering box. Also check the rag joint (and u-joint) in the stub shaft between the firewall and the steering box. And where that shaft connects to things, when I first got my truck it was loose between that stub shaft and the steering shaft that goes into the cab.

A little bit of play goes a long ways in the steering box though.
Yeah but this is .. I dont know .. maybe 2... 4 inches of play either way at the steering wheel. So much so that when i drive it and someone is coming in the opposite direction i pay ALOTof attention.

I'll check the things some of the fellas mentioned here tonight.
 

BlackBII

Ranger Custom
Article Contributor
OTOTM Winner
TRS Banner 2010-2011
Truck of Month
Joined
Aug 14, 2007
Messages
7,895
Reaction score
982
Points
113
Location
UT
Vehicle Year
1989
Make / Model
Ford
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
Total Lift
5
Tire Size
33
Can we get some pics of the front axle? I will second what has been said so far; tie rod ends, bushings, rag joint, etc can all lead to sloppy steering.

As far as the wheels go, you'll want something like these:
Pro Comp 15 x 8, 3.75" backspacing, 5 x 4.5" bolt pattern
Wheels Link

You could run run a 32 x 11.50 as a compromise in size between 31 x 10.50 and 33 x 12.50. 33 x 10.50 do also exist.
 

Sponsored Ad


Sponsored Ad

Members online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top