• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

in need of pcm pinout diagram


ryanohn

New Member
Joined
Aug 31, 2012
Messages
127
Reaction score
0
Points
0
Location
Brighton, Michigan
Vehicle Year
1991/1989
Make / Model
Ford
Engine Size
7.3 IDI
Transmission
Manual
so i am looking for pcm pinout for 1991 ford ranger 4.0 and 1992 f250 7.3 pcm pinout. i am trying to splice the two harness together. i would like the pin out so i can start making the new wiring harness and suggestions on websites to find the pin outs and splicing them together. any information is helpful
 


adsm08

Senior Master Grease Monkey
Supporting Member
Article Contributor
Ford Technician
TRS 20th Anniversary
Joined
Sep 20, 2009
Messages
34,623
Reaction score
3,613
Points
113
Location
Dillsburg PA
Vehicle Year
1987
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0
Transmission
Manual
2WD / 4WD
4WD
Tire Size
31X10.50X15
Why?

I am uncertain what end you are actually trying to accomplish here.
 

bobbywalter

TRS Technical Staff
TRS Event Staff
V8 Engine Swap
TRS Technical Advisor
TRS Banner 2012-2015
TRS 20th Anniversary
Ugly Truck of Month
TRS Event Participant
Joined
Aug 9, 2007
Messages
23,470
Reaction score
4,667
Points
113
Location
woodhaven mi
Vehicle Year
1988
Make / Model
FORD mostly
Engine Type
V8
Engine Size
BIGGER
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
sawzall?
Tire Size
33-44
My credo
it is easier to fix and understand than "her"
that idi just needs power to the solo and some momentary glow heat to run depending of what fuel pump you want to run..

are you running the e4od? the system is basically stand alone for that, just power the upstream side of its diode.


from there use a ops for the electric fuel pump if you prefer electric, and make a glow system thats manual.


gauges are gauges...

the fuel manager is handy, nice to have the water in fuel sensor and light and glow indicator, not necessary though.


my truck has a pull handle to turn on the fuel pump and injection pump and crank the engine, with a button trigger for the glows. i fit the gm gauge shit to the ranger dash.


key power for most crank and run functions is the red with green stripe.
 
Last edited:

RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,291
Reaction score
8,296
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
so i am looking for pcm pinout for 1991 ford ranger 4.0 and 1992 f250 7.3 pcm pinout. i am trying to splice the two harness together. i would like the pin out so i can start making the new wiring harness and suggestions on websites to find the pin outs and splicing them together. any information is helpful
Here is the EEC-IV connector pin diagram and functions:
http://www.auto-diagnostics.info/ford_eec_iv

EEC-IV PCM was used from '83-'95
 
Last edited:

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top