• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

pats bypass for remote start


RangerSVT

RangerSVT

Oct 09 OTOTM
Article Contributor
V8 Engine Swap
OTOTM Winner
Solid Axle Swap
RBV's on Boost
ASE Certified Tech
TRS Banner 2010-2011
TRS Banner 2012-2015
Joined
Mar 15, 2009
Messages
7,883
Reaction score
53
Points
48
Location
TRS since 2002 - NW KY
Vehicle Year
19962002
Make / Model
Ford
Engine Size
GT-40 5.0L EFI W/AC
Transmission
Automatic
The instructions for 555 will tell you where to mount it...
SVT
 


--weezl--

--weezl--

June 2011 OTOTM Winner
Law Enforcement
OTOTM Winner
TRS Banner 2012-2015
Joined
May 26, 2010
Messages
8,495
Reaction score
182
Points
0
Location
hell
Vehicle Year
2007
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
is it actually necessary to solder all the connections, or are the 3 way splice connectors good enough?

so is it kinda like install the remote starter in fully then put the bypass in on top of that install?


if you guys don't mind, what i would like to do is scan the installation wiring diagram, and just write in where i think all the wires go, based on the diagram on bullydog's website and i'll post it up here, you guys tell me if it sounds right...
 
Ranger SVO

Ranger SVO

Member
Joined
Aug 9, 2007
Messages
340
Reaction score
6
Points
18
Location
Abilene Texas
Vehicle Year
1993
Make / Model
Ford
Engine Size
2.3 Turbo
Transmission
Manual
I always solder Remote Starts and Alarms. I want them to be as reliable as possible.

The PATS plug should be located in the column. Its a four pin plug.

The TX wire is Violet/Brown
The RX wire is Blue/ Gray
 

Attachments

Last edited:
Sasquatch_Ryda

Sasquatch_Ryda

Well-Known Member
Ford Technician
OTOTM Winner
Solid Axle Swap
Forum Staff - Retired
TRS Banner 2012-2015
Joined
Aug 8, 2007
Messages
7,916
Reaction score
108
Points
63
Age
36
Location
Terrace, BC, Canada
Vehicle Year
1991
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0L
Transmission
Automatic
2WD / 4WD
Solid Axle Swap 4x4
Tire Size
40s
Can't help you with that aftermarket bypass module, I always just use a ford one and splice it into whichever remote starter system I'm working with. Usually either Ford, CompuStar or Prostart.

Solder and tape all connections, no scotch locks.....
 
You must log in or register to reply here.

Sponsored Ad


Sponsored Ad

Members online

Total: 459 (members: 2, guests: 457)

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

Latest Album Photos

20240409_190831.jpg
20240409_190818.jpg
20240409_180824.jpg
20240409_182648.jpg
20240409_181010.jpg
20240408_175026.jpg
99 Ranger
20200706_161414.jpg
20240207_155117.jpg
20240207_155111.jpg
20240207_154537 - Copy.jpg
20240207_154500 - Copy.jpg

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top